CY28400OXI-2 Silicon Laboratories Inc, CY28400OXI-2 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
CY28400OXI-2
Manufacturer Part Number
CY28400OXI-2
Description
Clock Buffer PCIe buffer 1in 4out
Manufacturer
Silicon Laboratories Inc
Datasheet
1.CY28400OXC-2.pdf
(15 pages)
Specifications of CY28400OXI-2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Rev 1.0, November 21, 2006
Pin Description
Serial Data Interface
To enhance the flexibility and function of the clock buffer, a
two-signal serial interface is provided. Through the Serial Data
Interface, various device functions, such as individual clock
output buffers, can be individually enabled or disabled. The
registers associated with the Serial Data Interface initialize to
their default setting upon power-up, and therefore use of this
interface is optional. Clock device register changes are
normally made upon system initialization, if any are required.
The interface cannot be used during system operation for
power management functions.
Table 1. Command Code Definition
Table 2. Block Read and Block Write Protocol
2,3
6,7;9,10;20,19;
23,22
8,21
17
15
16
13
14
26
12
28
27
4
1,5,11,18,24
25
(6:0)
2:8
Bit
Bit
Pin
7
1
Slave address – 7 bits
0 = Block read or block write operation
1 = Byte read or byte write operation
Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be
'0000000'
Start
SRCT_IN, SRCC_IN
DIF[T/C][2:1] & [6:5]
OE_1, OE_6
HIGH_BW#
PWRDWN
SRC_STP
SCLK
SDATA
IREF
PLL/BYPASS#
VDD_A
VSS_A
VSS
VDD
OE_INV
Block Write Protocol
Name
Description
I/O,OC Open collector SMBus data
O,DIF 0.7V Differential Clock Outputs
Type
PWR
GND
PWR
I,DIF
GND
I, SE
I,SE
I,SE
I,SE
I,SE
I,SE
I
I
0.7V Differential inputs
3.3V LVTTL input for enabling differential outputs
Active HIGH if OE_INV = 0
Active LOW if OE_INV = 1
3.3V LVTTL input for selecting PLL bandwidth
0 = High BW, 1 = Low BW
3.3V LVTTL input for Power Down
Active LOW if OE_INV = 0
Active HIGH if OE_INV = 1
3.3V LVTTL input for SRC_STP. Disables stoppable outputs.
Active LOW if OE_INV = 0
Active HIGH if OE_INV = 1
SMBus Slave Clock Input
A precision resistor is attached to this pin to set the differential output
current
3.3V LVTTL input for selecting fan-out or PLL operation
3.3V Power Supply for PLL
Ground for PLL
Ground for outputs
3.3V power supply for outputs
Input strap for setting polarity of OE_[7:0], SRC_STP, and PWRDWN
Description
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operations from the controller. For
block write/read operation, the bytes must be accessed in
sequential order from lowest to highest byte (most significant
bit first) with the ability to stop after any complete byte has
been transferred. For byte write and byte read operations, the
system controller can access individually indexed bytes. The
offset of the indexed byte is encoded in the command code,
as described in Table 1.
The block write and block read protocol is outlined in Table 2
while Table 3 outlines the corresponding byte write and byte
read protocol. The slave receiver address is 11011100 (DCh).
2:8
Bit
1
Start
Slave address – 7 bits
Description
Block Read Protocol
Description
CY28400-2
Page 2 of 15