CS61574A-IL1 Cirrus Logic Inc, CS61574A-IL1 Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS61574A-IL1
Manufacturer Part Number
CS61574A-IL1
Description
Network Controller & Processor ICs IC T1/E1 Ln Intrfc Unit F/Strtum-4 apps
Manufacturer
Cirrus Logic Inc
Datasheet
1.CDB61574A.pdf
(34 pages)
Specifications of CS61574A-IL1
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
PLCC-28
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS61574A-IL1
Manufacturer:
CSI
Quantity:
5 530
Company:
Part Number:
CS61574A-IL1
Manufacturer:
CSI
Quantity:
6 100
Company:
Part Number:
CS61574A-IL1
Manufacturer:
CRYSTAL
Quantity:
5 510
Company:
Part Number:
CS61574A-IL1
Manufacturer:
CRYSTAL
Quantity:
365
Part Number:
CS61574A-IL1
Manufacturer:
CRYSTRL
Quantity:
20 000
Company:
Part Number:
CS61574A-IL12
Manufacturer:
CRYSTAL
Quantity:
5 510
Company:
Part Number:
CS61574A-IL1Z
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Company:
Part Number:
CS61574A-IL1ZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
TTIP, TRING - Transmit Tip, Transmit Ring, Pins 13 and 16.
Status
AIS - Alarm Indication Signal, Pin 11. (Extended Hardware Mode)
BPV- Bipolar Violation Strobe, Pin 6. (Extended Hardware Mode)
DPM - Driver Performance Monitor, Pin 11. (Hardware and Host Modes)
LOS - Loss of Signal, Pin 12.
MTIP, MRING - Monitor Tip, Monitor Ring, Pins 17 and 18. (Hardware and Host Modes)
Ordering Guide
26
The AMI signal is driven to the line through these pins. The transmitter output is designed to
drive a 75 Ω load between TTIP and TRING. A transformer is required as shown in Table A1.
AIS goes high when unframed all-ones condition (blue alarm) is detected, using the detection
criteria of less than three zeros out of 2048 bit periods.
BPV strobes high when a bipolar violation is detected in the received signal. B8ZS (or HDB3)
zero substitutions are not flagged as bipolar violations if the B8ZS (or HDB3) decoder has been
enabled.
DPM goes high if no activity is detected on MTIP and MRING.
LOS goes high when 175 consecutive zeros have been received. LOS returns low when the ones
density reaches 12.5% (based upon 175 bit periods starting with a one and containing less than
100 consectutive zeros) as prescribed in ANSI T1.231-1993. When in the loss of signal state
RPOS/RNEG or RDATA are forced low, and ACLKI (if present) is output on RCLK via the jitter
attenuator. If ACLKI is not present during LOS, RCLK is forced to the center frequency of the
crystal oscillator.
These pins are normally connected to TTIP and TRING and monitor the output of a line interface
IC. If the INT pin in the host mode is used, and the monitor is not used, writing "clear DPM" to
the serial interface will prevent an interrupt from the driver performance monitor.
Model
Z
Z
Frequency
T
T
1
FIFO Depth (Bits)
1 2
3
2
Package
CS61574A CS61575
, Lead-free
, Lead-free
DS154F3