PP007-WS-1 LECROY, PP007-WS-1 Datasheet

Page 1

... Instruction Manual LeCroy PP007-WR / PP007-WS Passive Probe PP007-WR-1 PP007-WR-2 PP007-WS-1 PP007-WS-2… Revision D – July 2004 ...

Page 2

... In exercising its warranty, LeCroy, at its option, will either repair or replace any assembly returned within the warranty period to the Customer Service Department of an authorized service center. However, this will be done only if the product is determined by LeCroy’s examination to be defective do to workmanship or materials, and the defect is not caused by misuse, neglect, accident, abnormal conditions of operation, or damaged resulting from attempted repair or modifications by a non-authorized service facility ...

Page 3

Safety Information This symbol appears on the product: This refers you to additional information contained in this manual. The corresponding information in the manual is similarly denoted. To avoid personal injury and to prevent fire or damage to the probe ...

Page 4

... Introduction The PP007- miniature high impedance passive probe. Its high input resistance and low capacitance make it ideal from general purpose probing of signals with frequency content from DC through several hundred MHz. The PP007 has a large selection of connection accessories, both supplied standard with the probe and available from LeCroy as optional accessories ...

Page 5

Specifications (continued) Operating Temperature Storage Temperature Altitude, Operating Cable Length Weight (probe only) Max. V versus Frequency, IN Measurement category (Vrms) 400 350 300 250 200 150 100 50 0 100 Frequency ...

Page 6

... Connectivity Accessories LeCroy provides over 30 individual accessories for the PP007-xx probe, which enable reliable connections to any physical requirement. In addition to those provided with the standard probe, several optional varieties are available either individually, or grouped in sets related to specific application needs. The PK007 series of connectivity accessories are compatible with any LeCroy 2.5 mm PP0x7 series probe. ...

Page 7

... The PCB adapter (LeCroy P/N PK007-015) is intended to be designed into and permanently installed in circuit boards to provide a reliable, high frequency test point which eliminates the need to hand hold the probe. Probe connected using PCB Adapter 14 PK007-016 Ground Spring (Not shown) PP007-OM-E Instruction Manual 1.5 mm (0.059”) PC Board hole size and pattern 15 PK007-014 Copper Pad 5 ...

Page 8

Optional Accessories Input Adapters and Clips 17 18 PK007-017 PK007-018 Single Lead Adapter Dual Lead Adapter 21 PK007-019 Pico Hook (For low voltage use only ≤ DC PK007-022 Adapter plug Adapter, 4 ...

Page 9

Ground Leads 25 PK007-024 Probe Tip Ground Lead w 0.8 mm Socket 28 PK007-026 Ground Llead with mini clip Ground Lead with 8 mm socket 31 PK007-029 Ground lead with 4 mm plug *The PK007-030 High Frequency compenated ground lead ...

Page 10

... Probe Connectivity Kits The following kits containing an assortment of probe connection accessories can be ordered directly from LeCroy. Refer to the illustrations on pages 6-9 for identification. PK701 Basic Adapter Kit replaces the common standard accessories, with 2 each of designators and 14; plus one adjustment tool (designator 3). ...

Page 11

Probe Compensation Proper compensation of the probe is required to assure good amplitude accuracy in the dynamic portions of the waveform being measured. LF compensation matches the probe to differences in oscilloscope input capacitance. The LF compensation should always be ...

Page 12

... Tip Selection and Exchange The PP007-xx probe is supplied with two tip styles. The spring tip, which is installed when the probe is shipped, combines a sharp point with on-axis compliance. This provides reliable connection under a wide range of physical interconnect situtations. A rigid tip is also supplied. While lacking the on-axis compliance feature of the spring tip, the rigid tip has a larger diameter and is more robust when exposed to physical stress at the tip ...