DG406DN Vishay, DG406DN Datasheet - Page 5

• Manufacturer Part Number: DG406DN
• Description: Analog Multiplexer Single 16:1 28-Pin PLCC
• Manufacturer: Vishay
• Type: Analog Multiplexerr

Specifications of DG406DN

• Package: 28PLCC
• Maximum On Resistance: 120@12V Ohm
• Maximum Propagation Delay Bus To Bus: 350@±15V ns
• Maximum High Level Output Current: 30 mA
• Multiplexer Architecture: 16:1
• Maximum Turn-off Time: 300@12V ns
• Maximum Turn-on Time: 600@12V ns
• Power Supply Type: Single|Dual

Notes:
a. Refer to PROCESS OPTION FLOWCHART.
b. Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
f. V
g. R
h. Worst case isolation occurs on Channel 4 due to proximity to the drain pin.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Document Number: 70061
S11-0179-Rev. J, 07-Feb-11
SPECIFICATIONS
Parameter
Analog Switch
Analog Signal Range
Drain-Source
On-Resistance
R
Channels
Source Off Leakage Current
Drain Off Leakage Current
Drain On Leakage Current
Dynamic Characteristics
Switching Time of Multiplexer
Enable Turn-On Time
Enable Turn-Off Time
Charge Injection
Power Supplies
Positive Supply Current
Negative Supply Current
DS(on)
IN
DS(on)
= input voltage to perform proper function.
Matching Between
g
= R
DS(on)
max. - R
e
a
(for Single Supply)
DS(on)
V
min.
R
Symbol
t
R
t
OFF(EN)
ANALOG
ON(EN)
t
I
I
I
OPEN
DS(on)
S(off)
D(off)
D(on)
DS(on)
Q
I+
I-
V
V
Unless Otherwise Specified
EN
S1
V
V
C
V
sequence each switch on
D
S
sequence each
V
V
= 8 V, V
V
L
D
= 0 V or 5 V, V
AL
S
= 10 V or 0.5 V
= 0.5 V or 10 V
INH
= 1 nF, V
V
= 3 V, 10 V, I
switch on
V+ = 12 V, V- = 0 V
= V
Test Conditions
EN
= 0.8 V, V
= 2.4 V, V
D
= 0 V
V
S8
= ± 10
S1
= 0 V, V
S
= 5 V
= 6 V, R
AH
A
S
INL
= 0 V or 5 V
= 2.4 V
= - 1 mA
= 0 V
IN
S
DG406
DG407
DG406
DG407
= 2.4 V
= 0
f
Temp.
Room
Room
Room
Room
Room
Room
Room
Room
Room
Room
Room
Room
Room
Full
Full
Full
b
- 0.01
Typ.
0.01
0.04
0.04
0.04
0.04
300
250
150
20
90
13
5
c
- 55 °C to 125 °C
Min.
- 20
- 20
0
A Suffix
d
Max.
120
450
600
300
DG406, DG407
12
30
75
d
Vishay Siliconix
- 40 °C to 85 °C
Min.
- 20
- 20
0
D Suffix
d
www.vishay.com
Max.
120
450
600
300
12
30
75
d
Unit
nA
pC
µA
ns

%
V
5