DG411DY Vishay, DG411DY Datasheet - Page 4

• Manufacturer Part Number: DG411DY
• Description: Analog Switch Quad SPST 16-Pin SOIC N
• Manufacturer: Vishay
• Type: Analog Switchr

Specifications of DG411DY

• Package: 16SOIC N
• Maximum On Resistance: 80@10.8V Ohm
• Maximum High Level Output Current: 30 mA
• Maximum Turn-off Time: 145@±15V ns
• Maximum Turn-on Time: 250@12V ns
• Switch Architecture: SPST
• Power Supply Type: Single|Dual

DG411, DG412, DG413
Vishay Siliconix
Notes:
a.Refer to process option flowchart.
b.Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d.The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e.Guaranteed by design, not subject to production test.
f. V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
www.vishay.com
4
SPECIFICATIONS
Parameter
Analog Switch
Analog Signal Range
Drain-Source
On-Resistance
Dynamic Characteristics
Turn-On Time
Turn-Off Time
Break-Before-Make
Time Delay
Charge Injection
Power Supplies
Positive Supply Current
Negative Supply Current
Logic Supply Current
Ground Current
IN
= input voltage to perform proper function.
50
45
40
35
30
25
20
15
10
5
0
On-Resistance vs. V
- 20
T
± 15 V
A
= 25 °C
- 15
e
- 10
a
V
Symbol
R
(for Unipolar Supplies)
ANALOG
V
I
t
DS(on)
t
GND
OFF
D
ON
t
I+
Q
I
± 20 V
I-
D
L
- 5
- Drain V oltage (V)
D
± 5 V
and Power Supply Voltage
± 8 V
0
V
V
g
I
V+ = 13.5 V, V
S
5
L
= 6 V, R
R
R
= - 10 mA, V
V
DG413 only, V
= 5 V, V
L
L
V+ = 12 V, V- = 0 V
S
Unless Specified
Test Conditions
= 300 , C
= 300 , C
=
10
V+ = 10.8 V,
8
± 10 V
g
V, see figure 2
IN
= 0 , C
± 12 V
15
= 2.4 V, 0.8 V
IN
D
L
L
= 0 or 5 V
=
S
= 35 pF
= 35 pF
20
= 8 V
3
L
= 10 nF
V, 8 V
f
Temp.
Room
Room
Room
Room
Room
Room
Room
Room
Room
Full
Full
Hot
Hot
Hot
Hot
Hot
Hot
b
300
250
200
150
100
50
On-Resistance vs. V
0
- 0.0001
- 0.0001
0.0001
0.0001
Typ.
175
0
40
95
25
25
c
2
- 55 °C to 125 °C
Min.
V+ = 3 V
V
4
- 1
- 5
- 1
- 5
L
V+ = 5 V
= 3 V
A Suffix
d
6
V
D
8 V
Max.
- Drain Voltage (V)
D
8
100
250
400
125
140
12
80
and Unipolar Supply Voltage
1
5
1
5
S11-0179-Rev. F, 07-Feb-11
d
10
12 V
Document Number: 70050
- 40 °C to 85 °C
Min.
12
- 1
- 5
- 5
D Suffix
d
14
15 V
V
Max.
L
16
100
250
315
125
140
12
80
= 5 V
1
5
1
5
20 V
d
18
Unit
pC
µA
ns
V

20