BFC238363682 Vishay, BFC238363682 Datasheet - Page 21

• Manufacturer Part Number: BFC238363682
• Description: Cap Film 0.0068uF 2000VDC/700VAC PP 5% 17.5 X 8.5 X 17mm RDL 7.5mm T/R
• Manufacturer: Vishay

Specifications of BFC238363682

• Package/case: 17.5(Max) X 8.5(Max) X 17(Max)
• Mounting: Through Hole
• Capacitance Value: 0.0068 uF
• Voltage: 2000|700 Vdc|Vac
• Dielectric: PP
• Lead Pitch For Radial: 7.5 mm
• Product Length: 17.5(Max) mm
• Product Depth: 8.5(Max) mm
• Tolerance: 5 %
• Operating Temperature: -55 to 105 °C

POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of
the free air ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors”.
The component temperature rise (ΔT) can be measured (see section “Measuring the component temperature” for more details)
or calculated by ΔT = P/G:
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
The temperature is measured in unloaded (T
The temperature rise is given by ΔT = T
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described
hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference
suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (U
2. The peak-to-peak voltage (U
3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
Document Number: 28124
Revision: 03-Mar-10
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by U
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration.
temperature rise).
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat Conductivity”
2
×
• ΔT = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
T
∫
0
⎛
⎝
dU
------- -
dt
⎞
⎠
2
×
dt
<
U
Rdc
AC and Pulse Double Metallized Polypropylene
P
×
) shall not be greater than the rated DC voltage (U
Film Capacitors MMKP Radial Potted Type
⎛
⎝
dU
------- -
dt
⎞
⎠
rated
P-P
) shall not be greater than 2
C
- T
For technical questions, contact:
amb
amb
.
) and maximum loaded condition (T
√
2 x U
Rac
to avoid the ionisation inception level
[e-mail]
Thermocouple
Rdc
)
C
).
Vishay BCcomponents
MMKP 383
www.vishay.com
Rdc
and
207