MT88E46ASR1 Zarlink, MT88E46ASR1 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/7/726/zarlink_sml.jpg)
MT88E46ASR1
Manufacturer Part Number
MT88E46ASR1
Description
Caller ID CMOS 3.58MHz 3.3V/5V 20-Pin SOIC T/R
Manufacturer
Zarlink
Datasheet
1.MT88E46ASR1.pdf
(23 pages)
Specifications of MT88E46ASR1
Package
20SOIC
Telecommunication Standards Supported
Bellcore GR-30-CORE|SR-TSV-002476|TIA/EIA-716|TIA/EIA-777
Fabrication Technology
CMOS
Maximum Data Rate
1.212 KBd
Typical Operating Supply Voltage
3.3|5 V
Typical Supply Current
4.3 mA
Operating Frequency
3.58 MHz
Data Sheet
•
After the ACK-Sender or Backup ACK-Sender detected
CAS, it must monitor the line for the line HIGH state,
which can happen only if all off hook CPEs also detected
CAS. Hence if the ACK-Sender or Backup ACK-Sender
is an on hook CPE, even if it falsely detected CAS, talkoff
can occur only if all off hook CPEs also falsely detected
CAS. Thus in the situation where the ACK-Sender or
Backup ACK-Sender is an on hook CPE using the
MT88E46 on hook mode detection algorithm, talkoff
protection is provided by the off hook CPEs. The on hook
mode has been optimized to be more talkdown immune so
that in this situation the on hook CPE will be successful in
fulfilling its ACK-Sender or Backup ACK-Sender
responsibility.
FSK Demodulation
The FSK demodulator is compatible with Bellcore SR-
TSV-002476, TIA/EIA-716 and TIA/EIA-777 standards.
It is capable of both Bell 202 and CCITT V.23 formats
transparently. FSK demodulation is available at the GS1
input op-amp only.
FSK Data Interface
The MT88E46 provides a powerful dual mode 3-wire
interface so that the data bytes in the demodulated FSK bit
stream can be extracted without the need either for an
external UART or for the CPE’s microcontroller to
perform the function in software.
The interface is specifically designed for the 1200 baud
rate and is consisted of 3 signals: DATA, DCLK (Data
Clock) and DR (Data Ready). DATA is an output pin.
DCLK is an input output pin. DR uses the dual purpose
output pin DR/DET. When FSK is selected it is the DR
signal.
Two FSK interface modes (modes 0 and 1) are selectable
via the CB0 pin. In mode 0, the FSK bit stream is output
directly. In mode 1, the data byte and the trailing stop bit
are stored in a 9 bit buffer. If mode 1 is used, the CB0 pin
can be connected to Vdd. If mode 0 is used and full chip
CPE shall immediately become the ACK-Sender, go
off hook no later than 35 ms after the start of the
line HIGH state, complete the CAS-ACK
handshake, and remain as ACK-Sender for the
duration of the call. This situation can happen if the
designated ACK-Sender and the Backup ACK-
Sender are not MEI compliant.
After going off hook the ACK-Sender shall begin
transmission of the ACK no earlier than 30 ms and
no later than 40 ms after the leading edge of the line
HIGH voltage transition.
power down is not required, the CB0 pin can be connected
to Vss.
In Bellcore’s off hook protocol, a Type 2 CPE should
restore the voicepath within 50 ms after the end of the
FSK signal. Due to noise, end of carrier detection is not
always reliable. The TIA/EIA-777 standard requires the
CPE to detect the end of FSK when any one of the
following occurs:
•
•
•
FSK Data Interface Mode 0 - Bit Stream Mode
This mode is selected when the CB0 pin is low. In this
mode the FSK data is output directly to the DATA pin.
DCLK and DR are timing signal outputs (see Figure 14).
For each received stop and start bit sequence, the
MT88E46 outputs a fixed frequency clock string of 8
pulses at the DCLK pin. Each DCLK rising edge occurs in
the middle of a DATA bit of the FSK byte. DCLK is not
generated for the start and stop bits. Consequently, DCLK
will clock only valid data into a peripheral device such as
a serial to parallel shift register or into a microcontroller.
The MT88E46 also outputs an end of word pulse DR
(Data Ready). DR goes low for half a nominal bit time at
the beginning of the trailing stop bit. It can be used to
interrupt a microcontroller or cause a serial to parallel
converter to parallel load its data into the microcontroller.
If a shift register is not used, DCLK and DATA may
occupy 2 bits of a microcontroller’s input port. The
microcontroller polls the input port and saves the DATA
bit when DCLK changes from low to high. When DR goes
low, the word may then be assembled from the last 8
saved bits.
Since the DR rising edge occurs in the middle of the
trailing stop bit, it can be used to read the stop bit to check
for framing error. Alternatively, at the DR falling edge the
microcontroller can set a timer for a 1/2400 second
timeout and read the stop bit at DATA when the timer
times out.
DATA may also be connected to a personal computer’s
serial communication port after conversion from CMOS
to RS-232 voltage levels.
FSK Data Interface Mode 1 - Buffer Mode
This mode is selected when the CB0 pin is high. In this
mode the received byte is stored on chip. At the end of a
absence of carrier signal or,
more than five framing errors (trailing stop bit a 0
instead of a 1) have been detected in the FSK
message or,
more than 150 ms of continuous mark signal or
space signal has been detected.
MT88E46
9