MT88E45BNR Zarlink, MT88E45BNR Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/7/726/zarlink_sml.jpg)
MT88E45BNR
Manufacturer Part Number
MT88E45BNR
Description
Caller ID CMOS 3.58MHz 3.3V 20-Pin SSOP T/R
Manufacturer
Zarlink
Datasheet
1.MT88E45BS1.pdf
(31 pages)
Specifications of MT88E45BNR
Package
20SSOP
Telecommunication Standards Supported
ANSI/TIA/EIA-716|ETSI/ETS 300 778-1|GR-30|SIN227|SIN242|SR-TSV-002476|TIA/EIA-777
Fabrication Technology
CMOS
Maximum Data Rate
1212 Bd
Typical Operating Supply Voltage
3.3 V
Typical Supply Current
2.8 mA
Minimum Operating Temperature
-40 °C
Maximum Operating Temperature
85 °C
Operating Frequency
3.58 MHz
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MT88E45BNR
Manufacturer:
MITEL
Quantity:
20 000
Company:
Part Number:
MT88E45BNR1
Manufacturer:
zarlink
Quantity:
2 600
MT88E45
6
Being able to detect CAS on Tip/Ring also makes the
MT88E45 suitable for BT on-hook CLIP applications.
For applications such as those in most European
countries where Tip/Ring CAS detection is not
needed, then the Tip/Ring and Hybrid op-amp gains
can be tailored independently to meet country
specific FSK and CAS signal level requirements
respectively. Note that since the Hybrid op-amp is for
CAS detection only, its gain can always be tailored
specifically for the CAS signal level.
The FSK demodulator is compatible with Bellcore,
ETSI and BT standards. The demodulated FSK data
is either output directly (bit stream mode) or stored in
a one byte buffer (buffer mode). In the buffer mode,
the stop bit immediately following a byte is also
stored and can be shifted out after the data byte.
This facility allows for framing error checking
required in Type 2 CPEs. In the bit stream mode, two
timing signals are provided. One indicates the bit
sampling instants of the data byte, the other the end
of byte. A carrier detector indicates presence of
signal and shuts off the data stream when there is no
signal.
The entire chip can be put into a virtually zero
current power down mode. The input op-amps, FSK
demodulator, CAS detector and the oscillator are all
shut off. Furthermore, power management has been
incorporated to minimize operating current. When
FSK is selected the CAS detector is powered down.
When CAS is selected the FSK demodulator is
powered down.
Functional Description
3 to 5V Operation
The MT88E45’s FSK and CAS reject levels are
proportional to Vdd. When operated at Vdd equal 3V
+/- 10%, to keep the FSK and CAS reject levels as at
5V (nominal) the Tip/Ring and Hybrid op-amp gains
should be reduced from those of 5V. Gains for
nominal Vdd (with a +/- 10% variation) other than 3
or 5V can be chosen as interpolation between the 3
and 5V settings.
Input Configuration
The MT88E45 provides an input arrangement
comprised of two op-amps and a bias source (V
V
used to bias the op-amp inputs at Vdd/2. The Tip/
Ring op-amp (IN1+, IN1-, GS1 pins) is for connecting
to Tip and Ring. The Hybrid op-amp (IN2+, IN2-,
REF
is a low impedance voltage source which is
REF
).
GS2 pins) is for connecting to the telephone hybrid
or speech IC receive pair.
Either FSK or CAS detection can be selected for the
Tip/Ring connection, while the hybrid connection is
for CAS detection only. Phrased in another way, FSK
demodulation is always on Tip/Ring, while CAS
detection can be on Tip/Ring or Hybrid Receive. Tip/
Ring CAS detection is required for MEI and BT on-
hook CLIP, while Hybrid CAS detection is needed for
optimal CAS speech immunity.
The feedback resistor connected between GS1 and
IN1- can be used to adjust the Tip/Ring signal gain.
The feedback resistor connected between GS2 and
IN2- can be used to adjust the hybrid receive signal
gain. When the Tip/Ring op-amp is selected, the
GS2 signal is ignored. When the Hybrid op-amp is
selected, the GS1 signal is ignored.
Either or both op-amps can be configured in the
single ended input configuration shown in Figure 3,
or in the differential input configuration shown in
Figure 4.
Differential Input Amplifier
Voltage Gain
(A
C1 = C2
R1 = R4 (For unity gain R5= R4)
R3 = (R2R5) / (R2 + R5)
Input Impedance
(Z
Voltage Gain
(A
Figure 3 - Single Ended Input Configuration
Highpass Corner Frequency
f
-3dB
V
Figure 4 - Differential Input Configuration
IN
V
diff) = R5/R1
) = R
diff) = 2
= 1/(2 R
C
C2
C1
F
/ R
IN
IN
R1
R
C)
R1
R4
IN
2
+ (1/ C)
R3
2
Advance Information
Highpass Corner Frequency
f
-3dB
R2
R
R5
F
= 1/(2 R1C1)
IN+
IN-
GS
V
GS
IN+
IN-
V
REF
REF