FTLX8571D3BCL Finisar Corporation, FTLX8571D3BCL Datasheet
FTLX8571D3BCL
Specifications of FTLX8571D3BCL
Available stocks
Related parts for FTLX8571D3BCL
FTLX8571D3BCL Summary of contents
Page 1
... SFF- 5 8472 . The FTLX8571D3BCL is a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturer’s recommended settings for interoperating the host-board EDC PHY with a limiting receiver SFP+ module ...
Page 2
... FTLX8571D3BCL Product Specification – September 2009 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS 4 SDA 2-wire Serial Interface Data Line 5 SCL 2-wire Serial Interface Clock Line ...
Page 3
... Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V. 5. Testing methodology per SFF-8431. Rev 3.0 6. The FTLX8571D3BCL is a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturer’s recommended settings for interoperating the host-board EDC PHY with a limiting receiver SFP+ module. ...
Page 4
... FTLX8571D3BCL Product Specification – September 2009 IV. Optical Characteristics Parameter Transmitter Optical Modulation Amplitude (OMA) Average Launch Power Optical Wavelength RMS Spectral Width Optical Extinction Ratio Transmitter and Dispersion Penalty Average Launch power of OFF transmitter Tx Jitter Encircled Flux Relative Intensity Noise Receiver Receiver Sensitivity (OMA ...
Page 5
... FTLX8571D3BCL Product Specification – September 2009 400 MHz-km OM2 500 MHz-km 50μm OM3 2000 MHz-km Notes: 1. 10GBASE-SR/SW. Contact Finisar for higher data-rate support Tested with a 2 – 1 PRBS VI. Environmental Specifications Finisar 850nm SFP transceivers have a commercial operating temperature range from 0°C to +70°C case temperature. ...
Page 6
... FTLX8571D3BCL Product Specification – September 2009 VIII. Digital Diagnostic Functions Finisar FTLX8571D3BCL SFP+ transceivers support the 2-wire serial communication protocol as defined in the SFF-8472 very closely related to the E the GBIC standard, with the same electrical specifications. The standard SFP+ serial ID provides access to identification information that describes the transceiver’ ...
Page 7
... FTLX8571D3BCL Product Specification – September 2009 IX. Digital Diagnostic Specifications FTLX8571D3BCL transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Parameter Accuracy Internally measured transceiver temperature Internally measured transceiver supply voltage Measured TX bias current Measured TX output power Measured RX received average ...
Page 8
... FTLX8571D3BCL Product Specification – September 2009 X. Mechanical Specifications Finisar FTLX8571D3BCL SFP+ transceivers are compatible with the SFF-8432 specification for improved pluggable form factor, and shown here for reference purposes only. Bail color is beige. Figure 3. FTLX8571D3BCL Mechanical Dimensions. © Finisar Corporation - September 2009 Rev D ...
Page 9
... FTLX8571D3BCL Product Specification – September 2009 XI. PCB Layout and Bezel Recommendations © Finisar Corporation - September 2009 Rev D Figure 4. Page 9 ...
Page 10
... FTLX8571D3BCL Product Specification – September 2009 Figure 5. © Finisar Corporation - September 2009 Rev D Page 10 ...
Page 11
... FTLX8571D3BCL Product Specification – September 2009 XII. Host - Transceiver Interface Block Diagram © Finisar Corporation - September 2009 Rev D Figure 6-Host-Module Interface Page 11 ...
Page 12
... FTLX8571D3BCL Product Specification – September 2009 XIII. References 1. “Specifications for Enhanced 8.5 and 10 Gigabit Small Form Factor Pluggable Module ‘SFP+ ‘”, SFF Document Number SFF-8431, Revision 3.0. 2. “Improved Pluggable Formfactor”, SFF Document Number SFF-8432, Revision 4.2, April 18, 2007. 3. IEEE Std 802.3ae, Clause 52, PMD Type 10GBASE-SR. IEEE Standards Department ...