N25Q128A13BF840E NUMONYX, N25Q128A13BF840E Datasheet - Page 45
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
N25Q128A13BF840E
Manufacturer Part Number
N25Q128A13BF840E
Description
128MBQUAD IO,XIP VDFPN 8X6 3VT&R
Manufacturer
NUMONYX
Datasheet
1.N25Q128A13BSF40G.pdf
(180 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
N25Q128A13BF840E
Manufacturer:
MICRON
Quantity:
20 000
- Current page: 45 of 180
- Download datasheet (6Mb)
6.5.1
6.5.2
6.5.3
Table 7.
P/E Controller Status bit
The bit 7 of the Flag Status register represents the Program/Erase Controller Status bit, It
indicates whether there is a Program/Erase internal cycle active. When P/E Controller
Status bit is Low (FSR<7>=0) the device is busy; when the bit is High (FSR<7>=1) the
device is ready to process a new command.
This bit has the same meaning of Write In Progress (WIP) bit of the standard SPI Status
Register, but with opposite logic: FSR<7> = not WIP
It's possible to make the polling instructions, to check if the internal modify operations are
finished, both on the Flag Status register bit 7 or on WIP bit of the Status Register.
Erase Suspend Status bit
The bit 6 of the Flag Status register represents the Erase Suspend Status bit, It indicates
that an Erase operation has been suspended or is going to be suspended.
The bit is set (FSR<6>=1) within the Erase Suspend Latency time, that is as soon as the
Program/Erase Suspend command (PES) has been issued, therefore the device may still
complete the operation before entering the Suspend Mode.
The Erase Suspend Status should be considered valid when the P/E Controller bit is high
(FSR<7>=1).
When a Program/Erase Resume command (PER) is issued the Erase Suspend Status bit
returns Low (FSR<6>=0)
Erase Status bit
The bit 5 of the Flag Status Register represents the Erase Status bit. It indicates an erase
failure or a protection error when an erase operation is issued.
When the Erase Status bit is High (FSR<5>=1) after an Erase failure that means that the
P/E Controller has applied the maximum pulses number to the portion to be erased and still
failed to verify that it has correctly erased.
The Erase Status bit should be read once the P/E Controller Status bit is High.
7
6
5
4
3
2
1
0
BIT
P/E Controller (not WIP)
Erase Suspend
Erase
Program
VPP
Program Suspend
Protection
RESERVED
Flag Status Register
Description
Status
Status
Error
Error
Error
Status
Error
Note
45/180
Related parts for N25Q128A13BF840E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![N25Q128](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
128-mbit 3 V, Multiple I/o, 4-kbyte Subsector Erase On Boot Sectors, Xip Enabled, Serial Flash Memory With 108 Mhz Spi Bus Interface
Manufacturer:
Numonyx
Datasheet:
![rc28f320j3d75d](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Numonyx™ Embedded Flash Memory J3 V. D
Manufacturer:
Numonyx
Datasheet:
![JS28F256M29EWH](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Manufacturer:
NUMONYX
Datasheet:
![JS28F640P33T85](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Manufacturer:
NUMONYX
Datasheet: