SQM48T25025-NBB0 POWER ONE, SQM48T25025-NBB0 Datasheet
SQM48T25025-NBB0
Specifications of SQM48T25025-NBB0
Available stocks
Related parts for SQM48T25025-NBB0
SQM48T25025-NBB0 Summary of contents
Page 1
The new 25A SemiQ™ Family of DC-DC converters provide a high-efficiency single output in a size that is only 60% of industry-standard quarter-bricks, while preserving the same pinout and functionality. The 25A SQM48 Series converters of the SemiQ™ Family provide ...
Page 2
Electrical Specifications Conditions: T =25ºC, Airflow=300 LFM (1.5 m/s), Vin=48 Vdc, All output voltages, unless otherwise specified. A PARAMETER ABSOLUTE MAXIMUM RATINGS Input Voltage Operating Ambient Temperature Storage Temperature INPUT CHARACTERISTICS Operating Input Voltage Range Input Under Voltage Lockout Turn-on ...
Page 3
Operation Input and Output Impedance These power converters have been designed to be stable with no external capacitors when used in low inductance in- put and output circuits. However, in many applications, the inductance associated with the distribution from the ...
Page 4
Output Voltage Adjust /TRIM (Pin 6) The output voltage can be adjusted up 10% or down 20% for Vout ≥ 1.5 V, and ±10% for Vout = ...
Page 5
Protection Features Input Undervoltage Lockout Input undervoltage lockout is standard with this converter. The converter will shut down when the input voltage drops below a pre-determined voltage. The input voltage must be at least 35 V for the converter to ...
Page 6
The following pages contain specific plots or waveforms as- sociated with the converter. Additional comments for specific data are provided below. Test Conditions All data presented were taken with the converter soldered to a test board, specifically a 0.060” thick ...
Page 7
Start-up Information (using negative ON/OFF) Scenario #1: Initial Start-up From Bulk Supply ON/OFF function enabled, converter started via application of V See Figure E. Time Comments t ON/OFF pin is ON; system front end power is toggled 0 on, V ...
Page 8
... Ambient Temperature [°C] Fig. 2.5V.1: Available load current vs. ambient air temperature and airflow rates for SQM48T25025 converter with D height pins mounted vertically with air flowing from pin 3 to pin 1, MOSFET temperature 120 C, Vin = 48 V. MCD10085 Rev. 1.1, 08-Jul-10 ...
Page 9
SQM48T/S25025 (2.5 Volts Out) Fig. 2.5V.3: Turn-on transient at full rated load current (resis- tive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). ...
Page 10
SQM48T/S25025 (2.5 Volts Out) Fig. 2.5V.7: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with F tantalum + 1uF ce- ramic and Vin = 48 V. Time scale: 1 s/div. Fig. ...
Page 11
SQM48T/S25025 (2.5 Volts Out) 3.0 2.5 2.0 1.5 1.0 0 Iout [Adc] Fig. 2.5V.11: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has al- most no effect on ...
Page 12
Electrical Specifications: SQM48T/S25020 (2.0 Volts Out Conditions: T =25ºC, Airflow=300 LFM (1.5 m/s), Vin=48 Vdc, Vout=2.0 Vdc unless otherwise specified. A PARAMETER INPUT CHARACTERISTICS Maximum Input Current Input Stand-by Current Input No Load Current (0 load on the output) Input ...
Page 13
SQM48T/S25020 (2.0 Volts Out) Fig. 2.0V.3: Turn-on transient at full rated load current (resis- tive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). ...
Page 14
SQM48T/S25020 (2.0 Volts Out) Fig. 2.0V.7: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with F tantalum + 1uF ce- ramic and Vin = 48 V. Time scale: 1 s/div. Fig. ...
Page 15
SQM48T/S25020 (2.0 Volts Out) 3.0 2.5 2.0 1.5 1.0 0 Iout [Adc] Fig. 2.0V.11: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has al- most no effect on ...
Page 16
Electrical Specifications: SQM48T/S25018 (1.8 Volts Out) Conditions: T =25ºC, Airflow=300 LFM (1.5 m/s), Vin=48 Vdc, Vout=1.8 Vdc unless otherwise specified. A PARAMETER INPUT CHARACTERISTICS Maximum Input Current Input Stand-by Current Input No Load Current (0 load on the output) Input ...
Page 17
SQM48T/S25018 (1.8 Volts Out) Fig. 1.8V.3: Turn-on transient at full rated load current (resis- tive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). ...
Page 18
SQM48T/S25018 (1.8 Volts Out) Fig. 1.8V.7: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with F tantalum + 1uF ce- ramic and Vin = 48 V. Time scale: 1 s/div. Fig. ...
Page 19
SQM48T/S25018 (1.8 Volts Out) 2.0 1.5 1.0 0 Iout [Adc] Fig. 1.8V.11: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has al- most no effect on current limit ...
Page 20
Electrical Specifications: SQM48T/S25015 (1.5 Volts Out) Conditions: T =25ºC, Airflow=300 LFM (1.5 m/s), Vin=48 Vdc, Vout=1.5 Vdc unless otherwise specified. A PARAMETER INPUT CHARACTERISTICS Maximum Input Current Input Stand-by Current Input No Load Current (0 load on the output) Input ...
Page 21
SQM48T/S25015 (1.5 Volts Out) Fig. 1.5V.3: Turn-on transient at full rated load current (resis- tive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (0.5 V/div.). ...
Page 22
SQM48T/S25015 (1.5 Volts Out) Fig. 1.5V.7: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with F tantalum + 1uF ce- ramic and Vin = 48 V. Time scale: 1 s/div. Fig. ...
Page 23
SQM48T/S25015 (1.5 Volts Out) 2.0 1.5 1.0 0 Iout [Adc] Fig. 1.5V.11: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has al- most no effect on current limit ...
Page 24
Electrical Specifications: SQM48T/S25012 (1.2 Volts Out) Conditions: T =25ºC, Airflow=300 LFM (1.5 m/s), Vin=48 Vdc, Vout=1.2 Vdc unless otherwise specified. A PARAMETER INPUT CHARACTERISTICS Maximum Input Current Input Stand-by Current Input No Load Current (0 load on the output) Input ...
Page 25
SQM48T/S25012 (1.2 Volts Out) Fig. 1.2V.3: Turn-on transient at full rated load current (resis- tive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (0.5 V/div.). ...
Page 26
SQM48T/S25012 (1.2 Volts Out) Fig. 1.2V.7: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with F tantalum + 1uF ce- ramic and Vin = 48 V. Time scale: 1 s/div. Fig. ...
Page 27
SQM48T/S25012 (1.2 Volts Out) 1.5 1.0 0 Iout [Adc] Fig. 1.2V.11: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has al- most no effect on current limit characteristic. ...
Page 28
Physical Information 1 TOP VIEW 2 3 SIDE VIEW SQM48S Pinout (Surface Mount) 1 TOP VIEW 2 3 SIDE VIEW SQM48T Pinout (Through-hole) MCD10085 Rev. 1.1, 08-Jul-10 TM SemiQ Family 25A DC-DC Converters All dimensions are in inches [mm] ...
Page 29
Converter Part Numbering/Ordering Information Product Input Mounting Rated Load Series Voltage Scheme SQM 1/8 S Brick 36-75 V Surface Format Mount Product Input Mounting Rated Load Series Voltage Scheme SQM 1/8 T Brick 36-75 ...
Page 30
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of ...