SSQE48T20033-NAA0G POWER ONE, SSQE48T20033-NAA0G Datasheet
SSQE48T20033-NAA0G
Specifications of SSQE48T20033-NAA0G
Related parts for SSQE48T20033-NAA0G
SSQE48T20033-NAA0G Summary of contents
Page 1
... Small size and low-profile Description The new SSQE48T20033 DC-DC converter is an open frame sixteenth-brick DC-DC converter that conforms to the Distributed Open Standards Architecture (DOSA) specifications. The converter operates over an input voltage range VDC, and provides a tightly regulated output voltage with an output current The output is fully isolated from the input and the converter meets Basic Insulation requirements permitting a positive or negative output configuration ...
Page 2
... Vout can be increased up to 10% via the sense leads or 10% via the trim function. However, the total output voltage trim from all sources shall not exceed 10 order to ensure specified operation of overvoltage protection circuitry. NOM OUT ZD-02087 Rev. 2.0 SSQE48T20033 DC-DC Converter 36-75 VDC Input; 3.3 VDC Output Notes Continuous Industry-standard equations (3.3V) Percent ...
Page 3
... Load Change 50%-75%-50% of Iout Max , di/ A/μs Settling Time Vout Efficiency 100% Load 50% Load Additional Notes: 2 Operating ambient temperature range is -40 º ºC ZD-02087 Rev. 2.0 SSQE48T20033 DC-DC Converter 36-75 VDC Input; 3.3 VDC Output Notes 100 36VDC , I =20ADC IN OUT Vin = 48V, converter disabled ...
Page 4
... The device must be capable of sinking low level voltage of 0 external voltage source (±20 V maximum) may be connected directly ZD-02087 Rev. 2.0 SSQE48T20033 DC-DC Converter 36-75 VDC Input; 3.3 VDC Output to the ON/OFF input, in which case it must be capable of sourcing or sinking depending on the signal polarity. See the Startup Information section for system timing waveforms associated with use of the ON/OFF pin ...
Page 5
... Fig. C: Configuration for increasing output voltage. To decrease the output voltage (Fig. D), a trim resistor should be connected between the T-DECR TRIM (Pin 6) and SENSE(-) (Pin 5), with a value of: ZD-02087 Rev. 2.0 SSQE48T20033 DC-DC Converter 36-75 VDC Input; 3.3 VDC Output R T DECR where, ...
Page 6
... An effective internal LC differential filter significantly reduces input reflected ripple current, and improves EMC. With the addition of a simple external filter, all versions of the SSQE48T20033 converters pass the requirements of Class B conducted emissions per EN55022 and FCC requirements. Please contact Power-One Applications Engineering for details of this testing ...
Page 7
... OUT ) ≤ 200 ms, the total converter For the condition startup time ( typically 205 ms. For ( startup will be typically 5 ms after release of ON/OFF pin. ZD-02087 Rev. 2.0 SSQE48T20033 DC-DC Converter 36-75 VDC Input; 3.3 VDC Output V IN ON/OFF STATE OFF ON V OUT ...
Page 8
... The output current at which any FET junction temperature does not exceed a maximum specified temperature of 125 °C as indicated by the thermographic image, or ZD-02087 Rev. 2.0 SSQE48T20033 DC-DC Converter 36-75 VDC Input; 3.3 VDC Output (ii) The temperature of the transformer does not exceed 125 °C, or (iii) The nominal rating of the converter. ...
Page 9
... LFM (1 m/s) 300 LFM (1.5 m/s) 400 LFM (2 m/s) 500 LFM (2.5 m/ Figure 1. Available load current vs. ambient air temperature and airflow rates for SSQE48T20033 converter mounted vertically with air flowing from pin 1 to pin 3, Vin = 48 V. Note: NC – Natural convection ...
Page 10
... Load Current, A Figure 4. Power dissipation vs. load current and input voltage for SSQE48T20033 converter mounted vertically with air flowing from pin 1 to pin 3at a rate of 300 LFM (1.5 m/s) and 40C 55C 6 70C 5 85C Load Current, A Figure 5 ...
Page 11
... Vin = 48 V. Refer to Figure 11 for test setup. Time scale: 1 µs/div. ZD-02087 Rev. 2.0 SSQE48T20033 DC-DC Converter 36-75 VDC Input; 3.3 VDC Output Figure 13. Input reflected ripple-current, i measured at input terminals at full rated load current and Vin = 48 V. Refer to Figure 11 for test setup. Time scale: 1 µ ...
Page 12
... V hole 20 ADC Format The example above describes P/N SSQE48T20033-NAB0G: 36-75 V input, through-hole 3.3 V output, negative ON/OFF logic, maximum height of 0.374”, 0.145” pins, standard feature set, and RoHS compliant for all 6 substances. Consult factory for availability of other options. Notes: 1 ...