YNS05S10-0 POWER ONE, YNS05S10-0 Datasheet - Page 8

• Manufacturer Part Number: YNS05S10-0
• Description: Module DC-DC 1-OUT 0.7525V to 3.63V 10A 36W 6-Pin SMD T/R
• Manufacturer: POWER ONE
• Type: Step Downr

Specifications of YNS05S10-0

• Package: 6SMD
• Output Current: 10 A
• Output Voltage: 0.7525 to 3.63 V
• Input Voltage: 5 V
• Number Of Outputs: 1
• Output Power: 36 W

The following pages contain specific plots or
waveforms associated with the converter. Additional
comments for specific data are provided below.
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprised of two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
All measurements requiring airflow were made in the
vertical and horizontal wind tunnels using Infrared
(IR)
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
operating
Thermographic
capability is not available, then thermocouples may
be used. . The use of AWG #40 gauge thermocouple
is recommended to ensure measurement accuracy.
Careful routing of the thermocouple leads will further
minimize measurement error. Refer to Fig. F for the
optimum measuring thermocouple location.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 and Figs. x.2 for
maximum
temperature was varied between 25 °C and 85 °C,
with airflow rates from 30 to 500 LFM (0.15 m/s to
2.5 m/s), and vertical and horizontal mountings. The
airflow during the testing is parallel to the short axis
of the converter, going from pin 1 and pin 6 to
pins 2–5.
MCD10193 Rev. 1.0, 21-Jun-10
Fig. F: Location of the thermocouple for thermal testing.
thermography
temperatures
temperature
imaging
and
is
of
in
thermocouples
preferable;
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 10 A
120°C.
the
application.
Ambient
if
this
for
Page 8 of 25
YNS05S10 DC-DC Converter Data Sheet
For each set of conditions, the maximum load
current is defined as the lowest of:
(i) The output current at which any MOSFET
temperature does not exceed a maximum specified
temperature
thermographic image, or
(ii) The maximum current rating of the converter
(10 A).
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on the
PCB at the thermocouple location shown in Fig. F
should not exceed 120 °C in order to operate inside
the derating curves.
Efficiency
Fig. x.3 shows the efficiency vs. load current plot for
ambient temperature of 25 ºC, airflow rate of
200 LFM (1 m/s) and input voltages of 4.5 V, 5.0 V,
and 5.5 V. Fig. x.4 is for input voltages of 3.0 V,
3.3 V, and 3.6 V , and for output voltages ≤ 2.5 V.
Power Dissipation
Fig. 3.3V.4 shows the power dissipation vs. load
current plot for Ta = 25 ºC, airflow rate of 200 LFM
(1 m/s) with vertical mounting and input voltages of
4.5 V, 5.0 V, and 5.5 V, and output of 3.3 V.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1 μF ceramic
capacitor.
The output voltage ripple and input reflected-ripple
current waveforms are obtained using the test setup
shown in Fig. G.
Fig. G: Test Setup for measuring input reflected-ripple
currents, i
Vsource
inductance
source
1 H
s
and output voltage ripple.
www.power-one.com
capacitor
C
4x47 F
ceramic
IN
(120°C)
Y-Series
Converter
DC-DC
as
indicated
capacitor
ceramic
1 F
by
capacitor
ceramic
C
47 F
O
the
Vout