ZY1015G-T2 POWER ONE, ZY1015G-T2 Datasheet
ZY1015G-T2
Specifications of ZY1015G-T2
Related parts for ZY1015G-T2
ZY1015G-T2 Summary of contents
Page 1
Applications Low voltage, high density systems with Intermediate Bus Architectures (IBA) Point-of-load regulators for high performance DSP, FPGA, ASIC, and microprocessor applications Industrial computing, servers, and storage Broadband, networking, optical, and wireless communications systems Active ...
Page 2
... Packaging option is used only for ordering and not included in the part number printed on the POL converter label. 3 The evaluation board is available in only one configuration: ZY1015-K1. Example: ZY1015G-T3: A 50-piece reel of RoHS compliant POL converters. Each POL converter is labeled ZY1015G. 2. Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings may cause performance degradation, adversely affect long- term reliability, and cause permanent damage to the POL converter ...
Page 3
Electrical Specifications Specifications apply at the input voltage from 3V to 14V, output load from 0 to 15A, ambient temperature from - 40°C to 85°C, output capacitance consisting of 110F ceramic and 220F tantalum, and default performance parameters settings ...
Page 4
V [V] OUT 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 3.0 3.15 2.0 Figure 1. Output Voltage as a Function of Input Voltage and Output Current 4.3 Protection Specifications Parameter Type Threshold Threshold Accuracy Type Threshold ...
Page 5
Type Turn Off Threshold Temperature is decreasing after module was Turn On Threshold Threshold Accuracy From instant when threshold is exceeded until Delay the turn-off command is generated V is inside the PG window and stable OUT Logic V is ...
Page 6
EN Pin Polarity EN High Threshold EN Low Threshold Open Circuit Voltage From EN pin changing state to V Turn-On Delay From EN pin changing state to V Turn-Off Delay Feedback Loop Compensation (CCA0…CCA2 pins) CCA=7 (default) CCA=6 Recommended C ...
Page 7
Signal Specifications Parameter VDD ViL_s ViH_s Vhyst_s Hysteresis of input Schmitt trigger IoL_s LOW level sink current V(SYNC)=0.5V Ipu_s Pull-up current source V(SYNC)=0V Tr_s Maximum allowed rise time 10/90%VDD Cnode_s Freq_s Clock frequency of external SYNC line Tsynq T0 ...
Page 8
Typical Performance Characteristics 5.1 Efficiency Curves Vout=0.5V Vout=1. 1.5 3 4.5 6 7.5 9 Output Current, A Figure 2. Efficiency vs. Load. Vin=3.3V 100 Vout=0.5V Vout=2.5V 70 ...
Page 9
Vout=0.5V Vout=1.2V Vout=2.5V Vout=3. Input Voltage, V Figure 6. Efficiency vs. Input Voltage. Iout=15A 5.2 Turn-On Characteristics Figure 7. Tracking Turn-On. Vin=12V, Ch1 – V1, Ch2 ...
Page 10
Figure 10. Vin=12V, Vout=2.5V. CCA=05 Figure 11. Vin=12V, Vout=5V, CCA=05 Figure 12. Vin=5V, Vout=1V. CCA=03 ZD-00993 Rev. 1.6, 24-Jun-10 ZY1015 15A No-Bus POL Data Sheet 3V to 14V Input Figure 13. Vin=5V, Vout=2.5V. CCA=03 Figure 14. Vin=3.3V, Vout=1V. CCA=03 www.power-one.com ...
Page 11
Thermal Derating Curves 0LFM Figure 15. Thermal Derating Curves. Vin=12V, Vout=5. 0LFM Figure ...
Page 12
Typical Application Figure 17. Complete Schematic of Application with Three Independent Outputs. Intermediate Bus Voltage is from 8V to 14V. In this application four POL converters are configured to deliver three independent output voltages. POL1 and POL2 are connected ...
Page 13
Pin Assignments and Description Pin Pin Pin Buffer Name No. Type Type VLDO TEMP 3 A ENP DELAY 5 A CCA2 CCA1 CCA0 8 ...
Page 14
Pin and Feature Description 8.1 VLDO, Low Voltage Dropout The input of the internal linear regulator. always needs to be greater than 4.75V for normal operation of the POL converter. 8.2 IM, Interleave Mode The input with the internal ...
Page 15
Note: Due to noise sensitivity issues that may occur in limited cases recommended to avoid phase lag settings of 112.5 and 123.75 degrees, otherwise false PG and/or OV indications may occur. 8.15 –VS and +VS The differential voltage ...
Page 16
Mechanical Drawings ±0.30 7.7 Pin 1 2.03 1.27 20.3 ZD-00993 Rev. 1.6, 24-Jun-10 ZY1015 15A No-Bus POL Data Sheet 3V to 14V Input All Dimensions are in mm Tolerances: 0.1 0.5-10 0.2 10-100 Pin Coplanarity: 0.1 ...
Page 17
Pin 1 1.27 Figure 22. Recommended PCB Layout for Multilayer PCBs Notes: 1. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in ...