RWM08451002JB25E1 Vishay, RWM08451002JB25E1 Datasheet - Page 2
![Res Wirewound 10K Ohm 5% 11W ±75ppm/°C Conformal AXL Thru-Hole Box](/photos/26/38/263869/111206805-40_sml.jpg)
RWM08451002JB25E1
Manufacturer Part Number
RWM08451002JB25E1
Description
Res Wirewound 10K Ohm 5% 11W ±75ppm/°C Conformal AXL Thru-Hole Box
Manufacturer
Vishay
Type
Wirewoundr
Series
RWMr
Datasheet
1.RWM04103300JR15E1.pdf
(4 pages)
Specifications of RWM08451002JB25E1
Resistance Value
10 KOhm
Power Rating
11 W
Tolerance
5 %
Resistance
10kohm
Resistance Tolerance
± 5%
Voltage Rating
650V
Resistor Element Material
Wirewound
Svhc
No SVHC (15-Dec-2010)
External
RoHS Compliant
Temperature Coefficient
± 75ppm/°C
Resistor Case Style
8 X45
Rohs Compliant
Yes
Lead Free Status / RoHS Status
OVERLOAD
Heavy overloads can be endured in the form of short pulses
< 0.1 s. Particular requirements should be submitted to
Vishay Sfernice, specifying peak voltage, cycle and
environmental conditions.
RECOMMENDATIONS FOR USE
Since these components are high dissipation power
resistors, customers are advised to use a high melting point
solder.
For low ohmic values, the measurement becomes critical
and the connecting wires resistance is to be included. The
value is measured at 5 mm from the resistor body.
Document Number: 50008
Revision: 16-Oct-09
PERFORMANCE
TESTS
Short Time Overload
Temperature Cycling
Humidity (Steady State)
Terminal Strength
Load Life
ELECTRICAL SPECIFICATIONS
Tolerance
Temperature Coefficient + 75 ppm/°C typical
Dielectric Withstanding Voltage NF EN140000
Inductance
CECC 40201 - EN 140-201
40 °C ambient - R.H. 95 %
Enamelled Wirewound Power Resistors
2 full rotations of 180°
2 successive bending
Tensile test: 20 N
10 P
- 55 °C + 200 °C
CONDITIONS
25 °C ambient
25 °C ambient
For technical questions, contact:
90’/30’ cycle
1000 h at P
r
56 days
during 10 s
Standard
On request
r
Axial Leads
Group Mounting
In a still atmosphere, a distance between axes equal to five
times the resistor’s diameter is recommended.
Cabinet Mounting
•
•
•
These aspects should be considered by the end user.
Unventilated box: Dissipation should be reduced (see
dimensional drawing).
Forced
dissipation may be doubled or even trebled.
In any case: The surface temperature at the hottest point
should not exceed 450 °C.
sfer@vishay.com
REQUIREMENTS
± (1 % + 0.05 Ω)
± (1 % + 0.05 Ω)
± (2 % + 0.1 Ω)
± (5 % + 0.1 Ω)
± (5 % + 0.1 Ω)
Non inductive (Ayrton-Perry) winding available
ventilation:
500 V
± 1 % and ± 2 %
RMS
If
± 5 %
- 1 min - 10 mA
conditions
Vishay Sfernice
TYPICAL DRIFTS
± (0.5 % + 0.05 Ω)
± (0.5 % + 0.05 Ω)
± (0.5 % + 0.05 Ω)
± (0.1 % + 0.05 Ω)
± (1.5 % + 0.05 Ω)
are
www.vishay.com
appropriate,
RWM
89