4-1393211-6 Tyco Electronics, 4-1393211-6 Datasheet - Page 3

• Manufacturer Part Number: 4-1393211-6
• Description: Electromechanical Relay DPDT 30(NO)/3(NC)A 250/277VAC 5.485KOhm Flange Mount
• Manufacturer: Tyco Electronics
• Type: Power Relayr

Specifications of 4-1393211-6

• Contact Arrangement: DPDT
• Ac Coil Voltage: 250|277 V
• Mounting: Flange Mount

.913 MAX.
09-2010, Rev. 0910
www.te.com
© 2010 Tyco Electronics Ltd.
Dimensions
T92 – Mounting and termination code 5
Product code structure
Type
Enclosure
Contact arrangement
Coil Input
Mounting and termination
Contact material
Coil voltage
(23.19)
T92
P
S
7
A
1
2
3
4
5
2
Coil code: please refer to coil versions table
Dust protected plastic case
Wash-tight, tape sealed, plastic case (Mounting and termination code 1)
2 form A (2 NO)
AC voltage, 60Hz or 50/60 Hz (consult coil versions table)
Printed circuit board mount; printed circuit board terminals.
Panel mount via flanged cover; .250” (6.35mm) x .032” (.81mm) QC terminal
Panel mount via flanged cover; .187” (4.75mm) x .032” (.81mm) QC terminals for coil and .250” (6.35mm) for contacts
Panel mount via flanged cover, .187” (4.75mm) x .020” (.51mm) QC terminals for coil and .250” (6.35mm) for contacts.
Panel mount via flanged cover, M4 screws w/ captive pressure plates. Requires Enclosure P and Contact arrangement 7.
AgCdO
Top sealed, not wash-tight, not tape sealed on bottom (Mounting and termination codes 2, 3 & 4)
Printed circuit board / panel mount power relay T92
2.700 MAX.
2.345 ± .005
(59.56 ± .13)
2.135 MAX.
(68.58)
(54.23)
General Purpose Relays
Power Relays
T92 Series Two-pole 30A PCB or Panel Mount Relay
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
2.010 MAX.
(51.05)
.090 (2.29)
RAD. FOR
#8 SCREW
11 2 form C (2 CO)
4
1.36 MAX.
1.431 MAX.
AgSnOInO
(34.54)
(36.34)
Typical product code
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
2
6
.203 TYP.
Terminal assignment
Bottom view on pins
2 Form A
PCB layout
Bottom view on pins
T92 - Mounting and termination code 1
An alternate PC board layout utilizes .076 ± .003 (1.93 ± .076) diameter holes on the same
center-to-center spacing shown above. Use of the rectangular holes is recommended for
improved solderability.
Only necessary terminals are present on single throw models. Consequently, some holes
will be unnecessary for single throw models.
D
(16.00)
(9.27)
(5.16)
.365
.630
4
8
DC voltage
(4.12)
.162
(7.85)
.309
T92
(14.86)
0
1
.585
S
(41.10)
(Continued)
1.618
.052 TYP.
(1.32)
11
2 Form C
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
2
6
Potter & Brumfield
Potter & Brumfield
4
8
D
3
7
(4.70)
.185
.072 TYP.
2
(1.83)
(25.40)
1.000
0
1
2
-24
3