RT8202AGQW Richtek USA Inc, RT8202AGQW Datasheet - Page 10

• Manufacturer Part Number: RT8202AGQW
• Description: IC PWM CTRLR SYNC BUCK 16WQFN
• Manufacturer: Richtek USA Inc

Specifications of RT8202AGQW

• Pwm Type: Current Mode
• Number Of Outputs: 1
• Voltage - Supply: 4.5 V ~ 5.5 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-WFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Duty Cycle: -

RT8202/A/B
Application Information
The RT8202/A/B PWM controller provides high efficiency,
excellent transient response, and high DC output accuracy
needed for stepping down high voltage batteries to
generate low voltage CPU core, I/O, and chipset RAM
supplies in notebook computers. Richtek Mach
Response
providing 100ns “instant-on” response to load steps while
maintaining a relatively constant operating frequency and
inductor operating point over a wide range of input voltages.
The topology circumvents the poor load transient timing
problems of fixed-frequency current mode PWMs while
avoiding the problems caused by widely varying switching
frequencies in conventional constant-on-time and constant-
off-time PWM schemes. The DRV
modulator is specifically designed to have better noise
immunity for such a single output application.
PWM Operation
The Mach Response
the output filter capacitor's effective series resistance
(ESR) to act as a current sense resistor, so the output
ripple voltage provides the PWM ramp signal. Refer to the
function diagrams of RT8202/A/B, the synchronous high
side MOSFET is turned on at the beginning of each cycle.
After the internal one-shot timer expires, the MOSFET is
turned off. The pulse width of this one shot is determined
by the converter's input and output voltages to keep the
frequency fairly constant over the input voltage range.
Another one-shot sets a minimum off-time (400ns typ.).
On-Time Control (TON)
The on-time one-shot comparator has two inputs. One
input monitors the output voltage, while the other input
samples the input voltage and converts it to a current.
This input voltage proportional current is used to charge
an internal on-time capacitor. The on-time is the time
required for the voltage on this capacitor to charge from
zero volts to V
side switch directly proportional to output voltage and
inversely proportional to input voltage. The implementation
results in a nearly constant switching frequency without
the need a clock generator.
T
www.richtek.com
10
ON
= 3.85p x R
TM
OUT
technology is specifically designed for
TON
, thereby making the on-time of the high
x V
TM
,
OUT
DRV
/ (V
TM
IN
mode controller relies on
− 0.5)
TM
mode PWM
And then the switching frequency is :
Frequency = V
R
to TON pin.
Mode Selection (EN/DEM) Operation
The EN/DEM pin enables the supply. When EN/DEM is
tied to VDD, the controller is enabled and operates in
diode-emulation mode. When the EN/DEM pin is floating,
the RT8202/A/B will operate in forced-CCM mode.
Diode-Emulation Mode (EN/DEM = High)
In diode-emulation mode, RT8202/A/B automatically
reduces switching frequency at light-load conditions to
maintain high efficiency. This reduction of frequency is
achieved smoothly and without increasing V
load regulation. As the output current decreases from
heavy-load condition, the inductor current is also reduced,
and eventually comes to the point that its valley touches
zero current, which is the boundary between continuous
conduction and discontinuous conduction modes. By
emulation the behavior of diodes, the low-side MOSFET
allows only partial of negative current when the inductor
freewheeling current reach negative. As the load current
is further decreased, it takes longer and longer to discharge
the output capacitor to the level than requires the next
“ON” cycle. The on-time is kept the same as that in the
heavy-load condition. In reverse, when the output current
increases from light load to heavy load, the switching
frequency increases to the preset value as the inductor
current reaches the continuous condition. The transition
load point to the light load operation can be calculated as
follows (Figure 1) :
where T
I
LOAD
TON
is a resistor connected from the input supply (V
≈
ON
(V
IN
is On-time.
−
2L
OUT
V
OUT
/ (V
)
×
IN
T
x T
ON
ON
DS8202/A/B-04 March 2011
)
OUT
ripple or
IN
)