MAX7057ASE+ Maxim Integrated Products, MAX7057ASE+ Datasheet - Page 17

• Manufacturer Part Number: MAX7057ASE+
• Description: RF Transmitter IC TRANSMITTER ASK/FSK
• Manufacturer: Maxim Integrated Products

Specifications of MAX7057ASE+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

When matched to a 50Ω system, the MAX7057’s PA is
capable of delivering +9.2dBm of output power at
PAVDD = +2.7V with a broadband match. The output of
the PA is an open-drain transistor, which has internal
selectable shunt tuning capacitors (see the Variable
Capacitor section) for impedance matching. It is con-
nected to PAVDD or ROUT through a pullup inductor
for proper biasing. The internal selectable shunt capac-
itors make it easy for tuning when changing the output
frequency. The pullup inductor from the PA to PAVDD
or ROUT serves three main purposes: resonating the
capacitive PA output, providing biasing for the PA, and
acting as a high-frequency choke to prevent RF energy
from coupling onto the supply voltage. The pi network
between the PA output and the antenna also forms a
lowpass filter that provides attenuation for the higher-
order harmonics.
In many applications, the MAX7057 must be imped-
ance-matched to a small-loop antenna. The antenna is
usually fabricated out of a copper trace on a PCB in a
rectangular, circular, or square pattern. The antenna
has an impedance that consists of a lossy component
and a radiative component. To achieve high radiating
efficiency, the radiative component should be as high
as possible, while minimizing the lossy component. In
Table 17. Status Register (Address: 0x0C)
BIT
7-4
0
1
2
3
Output Matching to PCB Loop Antenna
300MHz to 450MHz Frequency-Programmable
fhi/lo[15]–fhi/lo[12]
RESERVED “0”
TxREADY
NoXTAL
NAME
Applications Information
X
______________________________________________________________________________________
Output Matching to 50 Ω
Internal Crystal Oscillator Status. High means oscillator is not in operation.
Transmitter Ready Status. High means PLL is locked and MAX7057 is ready to transmit data.
RESERVED. Set to 0 for normal operation.
RESERVED
ASK mode: Outputs flo[15:12].
FS K m od e: w hen d atai n p i n/b i t i s hi g h, outp uts fhi [ 15:12] ; w hen d atai n p i n/b i t i s l ow , outp uts fl o[ 15:12] .
addition, a loop antenna has an inherent loop induc-
tance associated with it (assuming the antenna is termi-
nated to ground). In a typical application, the
inductance of the loop antenna is approximately 50nH
to 100nH. The radiative and lossy impedances can be
anywhere from a few tenths of an ohm to 5Ω or 10Ω.
A properly designed PCB is an essential part of any
RF/microwave circuit. At high-frequency inputs and out-
puts, use controlled-impedance lines and keep them as
short as possible to minimize losses and radiation. At
high frequencies, trace lengths that are in the order of
λ/10 or longer act as antennas, where λ is the wave-
length.
Keeping the traces short also reduces parasitic induc-
tance. Generally, 1in of PCB trace adds about 20nH of
parasitic inductance. The parasitic inductance can
have a dramatic effect on the effective inductance of a
passive component. For example, a 0.5in trace con-
necting to a 100nH inductor adds an extra 10nH of
inductance, or 10%.
To reduce parasitic inductance, use wider traces and a
solid ground or power plane below the signal traces.
Using a solid ground plane can reduce the parasitic
inductance from approximately 20nH/in to 7nH/in. Also,
use low-inductance connections to the ground plane,
and place decoupling capacitors as close as possible
to all V
ASK/FSK Transmitter
FUNCTION
DD
pins.
Layout Considerations
17