MAX19985AETX+ Maxim Integrated Products, MAX19985AETX+ Datasheet - Page 20

• Manufacturer Part Number: MAX19985AETX+
• Description: RF Mixer IC MIXER DOWNCONV earity, 700MHz to 10
• Manufacturer: Maxim Integrated Products

Specifications of MAX19985AETX+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Dual, SiGe, High-Linearity, 700MHz to 1000MHz
Downconversion Mixer with LO Buffer/Switch
The RF and LO inputs are internally matched to 50Ω. No
matching components are required. The RF port input
return loss is typically 20dB over the RF frequency range
of 770MHz to 915MHz and return loss at the LO ports are
typically 20dB over the entire LO range. RF and LO inputs
require only DC-blocking capacitors for interfacing.
The IF output impedance is 200Ω (differential). For
evaluation, an external low-loss 4:1 (impedance ratio)
balun transforms this impedance to a 50Ω single-ended
output (see the Typical Application Circuit ).
Each channel of the MAX19985A has two pins (LO_BIAS,
IF_BIAS) that allow external resistors to set the internal
bias currents. Nominal values for these resistors are given
in Table 2. Larger-value resistors can be used to reduce
power dissipation at the expense of some performance
loss. See the Typical Operating Characteristics to evaluate
the power vs. performance tradeoff. If ±1% resistors are
not readily available, ±5% resistors can be substituted.
Table 2. Component Values
20
C10, C11, C12, C19, C20, C21
C9, C13, C15, C17, C18
______________________________________________________________________________________
C1, C2, C7, C8
COMPONENT
L1, L2, L4, L5
C14, C16
C3, C6
C4, C5
R1, R4
R2, R5
R3, R6
R7, R8
L3, L6
T1, T2
U1
Applications Information
Input and Output Matching
Externally Adjustable Bias
0.033µF
VALUE
0.01µF
330nH
150pF
1.2kΩ
698Ω
600Ω
500Ω
30nH
39pF
82pF
0Ω
4:1
—
—
Microwave capacitors (0402)
Microwave capacitors (0603)
Not used
Microwave capacitors (0402)
Microwave capacitors (0603)
Microwave capacitors (0402)
Wire-wound high-Q inductors (0805)
Wire-wound high-Q inductors (0603). Smaller values can be used at the expense of
some performance loss (see the Typical Operating Characteristics).
±1% resistors (0402). Larger values can be used to reduce power at the expense of
some performance loss (see the Typical Operating Characteristics).
±1% resistors (0402). Use for V
to reduce power at the expense of some performance loss (see the Typical
Operating Characteristics).
±1% resistors (0402). Use for V
±1% resistors (1206)
±1% resistors (0402)
Transformers (200:50)
Mini-Circuits TC4-1W-7A
MAX19985A IC
For applications requiring optimum RF-to-IF and LO-to-
IF isolation, connect a parallel combination of a low-
ESR inductor and a 500Ω resistor from LEXT_ (pins 15
and 31) to ground. When improved isolation is not
required, connect LEXT_ to ground using a 0Ω resis-
tance. See the Typical Operating Characteristics to
evaluate the isolation vs. inductor value tradeoff.
A properly designed PCB is an essential part of any
RF/microwave circuit. Keep RF signal lines as short as
possible to reduce losses, radiation, and inductance.
The load impedance presented to the mixer must be so
that any capacitance from both IF- and IF+ to ground
does not exceed several picofarads. For the best perfor-
mance, route the ground pin traces directly to the
exposed pad under the package. The PCB exposed
pad MUST be connected to the ground plane of the
PCB. It is suggested that multiple vias be used to con-
nect this pad to the lower-level ground planes. This
method provides a good RF/thermal-conduction path for
the device. Solder the exposed pad on the bottom of the
CC
CC
DESCRIPTION
= +5.0V applications. Larger values can be used
= +3.3V applications.
Layout Considerations
LEXT_ Inductors