MAX9986ETP Maxim Integrated Products, MAX9986ETP Datasheet - Page 3

• Manufacturer Part Number: MAX9986ETP
• Description: Up-Down Converters SiGe High-Linearity, 815MHz to 995MHz Do
• Manufacturer: Maxim Integrated Products

Specifications of MAX9986ETP

• Maximum Input Frequency: 995 MHz
• Maximum Power Dissipation: 2100 mW
• Maximum Operating Frequency: 250 MHz
• Maximum Power Gain: 11 dB
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: TQFN-20 EP

AC ELECTRICAL CHARACTERISTICS (continued)
(MAX9986 Typical Application Circuit, V
+3dBm, P
otherwise noted. Typical values are at V
+25°C, unless otherwise noted.) (Note 1)
Note 1: All limits include external component losses. Output measurements taken at IF output of the Typical Application Circuit.
Note 2: Operation outside this range is possible, but with degraded performance of some parameters.
Note 3: Compression point characterized. It is advisable not to operate continuously the mixer RF input above +12dBm.
Note 4: Measured with external LO source noise filtered so the noise floor is -174dBm/Hz. This specification reflects the effects of all
Note 5: Guaranteed by design and characterization.
Noise Figure
Noise Figure Under-Blocking
Small-Signal Compression
Under-Blocking Condition
LO Drive
Spurious Response at IF
LO1 to LO2 Isolation
LO Leakage at RF Port
LO Leakage at IF Port
RF-to-IF Isolation
LO Switching Time
RF Port Return Loss
LO Port Return Loss
IF Port Return Loss
Downconversion Mixer with LO Buffer/Switch
SNR degradations in the mixer, including the LO noise as defined in Maxim Application Note 2021.
RF
PARAMETER
= -5dBm, f
_______________________________________________________________________________________
SiGe High-Linearity, 815MHz to 995MHz
RF
= 815MHz to 995MHz, f
SYMBOL
2 x 2
3 x 3
CC
NF
CC
= +5V, P
= +4.75V to +5.25V, RF and LO ports are driven from 50Ω sources, P
Single sideband, f
f
f
f
f
( N ote 4)
P
f
f
2LO-2RF
3LO-3RF
P
T
P
P
50% of LOSEL to IF settled to within 2°
LO1/2 port selected,
LO2/1 and IF terminated
LO1/2 port unselected,
LO2/1 and IF terminated
LO driven at 0dBm, RF terminated into 50Ω,
differential 200Ω
R F
L O
B LOC K E R
I F
F U N D A M E N TA L
B LOC K E R
C
FUNDAMENTAL
LO
LO
LO
LO
= 190M H z
= +25°C (Note 5)
= 900M H z ( no si g nal )
= 1090M H z
RF
= +3dBm
= +3dBm
= +3dBm
= 960MHz to 1180MHz, f
= -5dBm, P
= 990M H z
= 911M H z
= 910M H z
CONDITIONS
= -5dBm
IF
LO
= 190MHz
= 0dBm, f
P
+ 8d Bm
P
+ 11d Bm
P
+ 8d Bm
P
+ 11d Bm
P
P
P
P
LO2 selected
LO1 selected
B LOC K E R
B LOC K E R
B LOC K E R
B LOC K E R
RF
RF
RF
RF
IF
= -10dBm
= -5dBm
= -10dBm
= -5dBm
RF
= 160MHz, f
= 910MHz, f
=
=
=
=
LO
LO
MIN
> f
42
42
-3
= 1070MHz, f
RF
, T
C
TYP
9.3
0.3
-47
-30
19
24
67
62
87
77
49
50
46
50
20
27
26
22
= -40°C to +85°C, unless
2
IF
MAX
= 160MHz, T
+3
LO
= -3dBm to
UNITS
dBm
dBm
dBm
dBc
dB
dB
dB
dB
dB
dB
dB
dB
ns
C
3
=