U2793B-NFSG3H Atmel, U2793B-NFSG3H Datasheet
U2793B-NFSG3H
Specifications of U2793B-NFSG3H
Available stocks
Related parts for U2793B-NFSG3H
U2793B-NFSG3H Summary of contents
Page 1
... Electrostatic sensitive device. Observe precautions for handling. 1. Description The IC U2793B is a 300-MHz quadrature modulator that uses Atmel UHF process. It features low current consumption, single-ended RF ports and adjust- ment-free application, which makes the device suitable for all digital radio systems, e.g., GSM, PCN, JDC and WLAN option, output level and spurious products are adjustable at pins 19 and 20. In conjunction with Atmel’ ...
Page 2
... Pin Configuration Figure 2-1. Pinning SSO20 U2793B ACGND 2 19 GND 3 18 RFO 4 17 ACGND 5 16 U2793B SPU BBAI BBAI LP1 LP2 GND GND GND LOI LOI VREF BBBI BBBI 4651E–CELL–07/06 ...
Page 3
... Baseband input B 12 BBBI Baseband input B inverse 13 VREF Reference voltage (2.5V) 14 LOI Input LO 15 LOI Input LO inverse, typically grounded 16 GND Ground 17 GND Ground 18 GND Ground 19 LP2 Output low pass and power control 20 LP1 Output low pass and power control 4651E–CELL–07/06 U2793B 3 ...
Page 4
... LP1 and LP2. In conjunction with a parallel resistor the output level can be adjusted to the following mixer stage without degration of LO suppression and noise performance which would decrease if the I/Q input level is reduced. 4. For T = –40°C to +85°C and V amb U2793B 4 Symbol ...
Page 5
... S Symbol Min. Typ. Max. – 3 – RFo RFO VSWR 1 SBS 35 45 RFo Pe <1 Ae < ±0.25 –137 N FL –143 SPU V 4 PUON V 2.375 2.5 2.625 Ref Zo 30 Ref U2793B Unit Type* dBm A deg dBm/Hz D µA D µ ...
Page 6
... Diagrams Figure 7-1. Figure 7-2. Figure 7-3. U2793B 6 Reference Voltage versus T amb 2.57 2.56 2.55 2.54 2.53 2.52 2.51 2.5 -40 0 Temperature (°C) OIP3 versus 150 MHz, Level -10 dBm amb -40 0 Temperature (°C) Supply Current versus T amb -40 0 Temperature (°C) 120 ...
Page 7
... Temperature (°C) Typical Output Power versus LO Frequency 250 mV (Differential) BBi 5 1.2 Vpp 0 -5 -10 -15 -20 100 mVpp 200 mVpp -25 400 mVpp -30 - 100 150 F (MHz) LO U2793B = 25 C amb 300 200 250 150 120 amb 1.0 Vpp 800 mVpp 600 mVpp 200 250 300 7 ...
Page 8
... Figure 7-7. U2793B 8 Typical Required V Input Signal (Differential) versus LO Frequency BBi for dBm and dBm O O 2000 1800 -1 dBm 1600 1400 1200 1000 800 600 400 200 100 150 F (MHz dBm -5 dBm 200 250 300 4651E–CELL–07/06 ...
Page 9
... Part List The above listed components result settling time of <20 µs. The use of other component values will require consideration for time requirements in burst-mode applications. 4651E–CELL–07/06 Evaluation Board Circuitry OUT inv , 100 pF = 100 50- Microstrip = optional U2793B GND B inv Ref U2793B LO 9 ...
Page 10
... Figure 8-2. PCB Layout Evaluation Board U2793B 10 4651E–CELL–07/06 ...
Page 11
... LO 14 Baseband i processing 10k 10k 100n 10. Ordering Information Extended Type Number U2793B-NFSH U2793B-NFSG3H 4651E–CELL–07/ for suppression which is in reference to < input offset. 2 Duty cycle Frequency 0° regenerator doubler 90° Duty cycle Frequency 0° regenerator doubler 90° Package SSO20 SSO20 , V ) ...
Page 12
... Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4651E-CELL-07/06 U2793B 12 History Page 1, PB-free logo deleted Page 3, Pin Desription table: Symbols of Pins 10,12, 15 changed Page 4, Abs. Max. Ratings table: Storage temperature values changed Page 5, row 4 ...
Page 13
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...