88019-37 AVX Corporation, 88019-37 Datasheet - Page 4

• Manufacturer Part Number: 88019-37
• Manufacturer: AVX Corporation

Specifications of 88019-37

• Lead Free Status / RoHS Status: Supplier Unconfirmed

megohms or 1,000 megohms microfarad, whichever is less.
not less than 1 second nor more than 5 seconds at +25°C. The charging current shall not exceed 50 milliamperes.
herein
should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance
requirements, and promotes economically advantageous life cycle costs.
MIL-PRF-123, MIL-PRF-39014, or
group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA.
source of supply.
appearance.
DEFENSE ELECTRONICS SUPPLY CENTER
3.1.4 Operating temperature range. The operating temperature range shall be -55°C to +125°C.
3.2 Electrical characteristics.
3.2.1 Rated voltage. The rated voltage shall be 100 V dc at +85°C, 50 V dc at +125°C.
3.2.2 Dielectric type. BX, in accordance with MIL-PRF-39014/5.
3.2.3 Voltage temperature limits. In accordance with MIL-PRF-39014/5.
3.2.4 Capacitance.
3.2.5 Dissipation factor (+25°C). 2.5 percent maximum (measured under the same conditions as capacitance).
3.2.6 Insulation resistance. Measured in accordance with
3.2.7 Dielectric withstanding voltage. Capacitors shall withstand a dc test potential of 250 percent of rated voltage for a period of
3.2.8 Capacitance tolerance. K = ±10 percent, M = ±20 percent.
3.3 Solderability of terminals. In accordance with MIL-PRF-39014.
3.4 Vibration. In accordance with
3.5 Shock. In accordance with MIL-PRF-39014.
3.6 Immersion cycling. In accordance with MIL-PRF-39014.
3.7 Moisture resistance. In accordance with MIL-PRF-39014.
3.8 Life. 200 percent of rated voltage applied at +125°C for 1,000 hours.
3.9 Thermal shock. In accordance with
3.10 Voltage conditioning. In accordance with MIL-PRF-39014, 200 percent of rated voltage.
3.11 Terminal strength. Capacitors shall withstand a steady pull of 5 pounds for 5 seconds in a direction parallel to the leads.
3.12 Marking. Marking shall be in accordance with
3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials
3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the
3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved
3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or
4. VERIFICATION
4.1 Sampling and inspection. Qualification sampling and inspection are not required.
(see
1.2), the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum.
DAYTON, OHIO
See table
I. Measured in accordance with
MIL-PRF-49470 Qualified Products Database
method 204 of
method 107 of
MIL-STD-202, test condition B (10 to 20,000 Hz, 15 g’s).
MIL-STD-1285
MIL-STD-202, test condition B except low temperature is -55°C.
method 302 of
method 305 of
except the capacitors shall be marked with the PIN as specified
SIZE
A
MIL-STD-202. At +25°C, rated voltage: 100,000
for at least one part, or perform the group A and
MIL-STD-202, 1 kHz at 1.0 V rms at +25°C.
CODE IDENT NO.
REV H
14933
PAGE
DWG NO.
88019
4