1-1705300-7 TE Connectivity, 1-1705300-7 Datasheet - Page 56
![](/photos/41/96/419631/pr1705300_sml.jpg)
1-1705300-7
Manufacturer Part Number
1-1705300-7
Description
Manufacturer
TE Connectivity
Datasheet
1.1-1705300-7.pdf
(116 pages)
Specifications of 1-1705300-7
Product Type
Connector
Card Type
2FF mini SIM
Card Guide Slots
Without
Pcb Mount Style
Surface Mount
Contact Retention
No
Connector Stabilization Ribs
Without
Height Above Pc Board (mm [in])
1.70 [0.067]
Card Stop
Without
Ejector Type
Push - Pull
Centerline (mm [in])
2.54 [0.100]
Durability Rating
5000 Cycles
Contact Base Material
Selective Gold
Number Of Contacts
6
Housing Color
Black
Housing Material
Liquid Crystal Polymer (LCP)
Ul Flammability Rating
UL 94V-0
Card Insertion Style
Normal Insertion
Card Detection Switch
Without
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Reflow solder capable to 245°C, Reflow solder capable to 260°C
Rohs/elv Compliance History
Always was RoHS compliant
Packaging Method
Tape & Reel
Lead Free Status / RoHS Status
Compliant
STAX™ Coax Connector
Features
• Low cost, low height and high
• Low insertion loss 0–0.5 dB
• VSWR <1.07 from 0–6 GHz
• Wide working range of deflec-
• Long term reliability and dura-
• Surface mount / pick and place
• Low board separation < 2.5 mm
• Technology can support board
• Easily modified free height
• No tooling required for height
• Modified prototype samples
Physical Properties
Board Separation:
2.5 mm ± 0.2 (Standard Part)
PCB Board Area:
4.0 mm diameter
Environmental Parameters
Operating Temperature:
–40 ºC to +125 ºC
Moisture:
0 to 100% RH
Electrical Properties
Contact Resistance:
< 50 mΩ
Insulation Resistance:
10
Dielectric Withstanding Voltage:
1000 Volt
Technical Documents
• Qualification Test Report – TR 368
• RF Performance Report – 00266
54
performance
from 0–6 GHz
tion
bility
separations <1.5 mm
modifications
within 2 weeks
12
Ω min
Products for Mobile Equipment
Connectors
STAX™ Coax Connector
Tyco Electronics’ STAX coax connector is
the first surface mount RF coax connector
on the market that uses elastomeric con-
nector technology to provide an economi-
cal means to achieve low board separation
while maintaining excellent RF signal
integrity between PCBs.
The connector uses laminated sections of
conductive and non-conductive silicone that
are tuned to provide a 50 ohm impedance
line between mated substrates.
The single piece construction of the STAX coax connector eliminates some of the signal anomalies
normally associated with mated pairs of metal contact coax connectors. The dimensional rela-
tionship of the inner and outer conductor is consistently maintained throughout the connector.
With its metal holder, the STAX coax connector can be surface mount soldered to the PCB. An
additional metal SMT holder aligns the connector to the mating PCB. If adequate PCB alignment
is already maintained by other means, the coax connector may not need the additional mating
receptacle and can become a blind-mating connector. This has an additional advantage in space
constrained mobile applications where very fine-pitch board-to-board connectors are also used.
619229-1 SMT STX Coaxial Connector Assembly
All specifications subject to change. Consult Tyco Electronics for latest specifications.
619238-2 SMT Mating Target Holder
Part No. 619229-1
Part No. 619238-2
Part No. 1442004-1
Conductive elastomer outer conductor
Conductive elastomer inner conductor
Non-conductive elastomer
STAX SMT Coax Connector Assembly: Consists of STAX coax elastomer
in round SMT holder.
Mating SMT Target Holder: Controls alignment between PCBs
STAX Coax Elastomer only: Used with customer furnished holder
PCB Pattern for Mating Target
PCB Pattern
Catalog 1654270-2
Center conductor
Dielectric material board
Outer conductor
Solder ring
Solder mask
Center conductor
Dielectric material board
Outer conductor
Solder ring
Solder mask
Revised 8-2007