126195-4 TE Connectivity, 126195-4 Datasheet - Page 176

• Manufacturer Part Number: 126195-4
• Description: ASSEMBLY TOOLS, TIP TOOL NICKEL FINISH
• Manufacturer: TE Connectivity
• Type: Extractor Toolr

Specifications of 126195-4

• Rohs Compliant: NA
• For Use With: 91067-2 Or M81969/1-02 Insertion/Extraction Tool
• Lead Free Status / Rohs Status: RoHS Not Applicable

Catalog 1308940
Revised 5-03
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
“G” Series Modular Connectors
Application Tooling
Entry Level Terminator (ELT),
1338600-1, -2, -3, -4 ,-5, -6
AMP-O-MATIC Stripper-
Crimper Machines,
1320895-1, -2
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
(Continued)
Semiautomatic Bench
Terminator for side- and
end-feed reeled terminals
and contacts. The ELT uses
a DC motor with gear box
drive. The result is a small-
footprint design that is fast
and quiet. Cycle time is less
than 0.400 seconds with an
operation sound level of
76dBa. With a crimp force
capacity of 3,000 pounds,
the ELT is available for all
but the highest crimp force
applications. A wide range
of optional equipment is
also available to meet
your specific application
requirements.
Semiautomatic bench
crimping machines that also
strip the wire, and are there-
fore used for terminating
jacketed cable. Feature
manual precision adjust-
ment of crimp height, keyed
strip blades for faster, more
accurate setups, and an
efficient scrap removal sys-
tem. All adjustments can be
made from the front of the
machines without special
tools. Available with crimp
quality monitoring.
The combination of the
Stripping Module with the
Entry Level Terminator (ELT)
or the AMP-O-LECTRIC
Model G Terminator
provides an economical
and proficient method of
stripping wire and crimping
terminals on the same
machine. Wires are stripped
moments before crimping,
meaning there is virtually no
chance of damaging wire
conductors during handling
or storage. Once the wire is
fed into the start sensor the
Stripping Module does the
rest, improving placement
accuracy.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
Specifications
Width — 16.8 [427]
Depth — 20.6 [523]
Height — 20 [510] without reel support
Weight — approx. 150 lb [68 kg]
Electrical — 100-240 VAC, 50/60 Hz,
6A (Note: Avg <1 A at 120 VAC when
used as a bench-top unit at 2,000 cycles
per hour operating rate)
Air — 90-100 psi [6.21-6.90 bar],
6 scfm [0.00282 m
use with air-feed applicators (Note:
Optional Air Feed Valve Assembly
Required)
Wire Range — Up to 14 AWG
[2.5 mm
For more information, request
catalog 1308382.
Specifications
Width — 14 [355]
Depth — 18 [457]
Height — 33 [838] without reel
Weight — 150 lb [68 kg]
Electrical — 120 VAC, 50 or
60 Hz, .5 A
Air — 80-100 psi [5.52-6.90 bar], 3.5
scfm [0.00165 m
Wire Range — 32-14 AWG
[0.03-2 mm
For more information, request
Catalog 65004.
Specifications
Wire Range Base Module —
0.03 mm
32 AWG may require special kit.)
Max. Insulation — .200 [5.08]
Cable Breakout — > 1.100 [29.00]
Strip Length — .100 - .400
[2.50 - 10.16]
Noise — Less than 82 dBA (Typical
at operator position with standard
mechanical feed applicator)
Weight — 4.53 Kilograms (10 lb)
Height — 5.000 [127.00]
Electrical — 100-240 VAC, 50/60 Hz,
single phase current, obtains power from
the terminator
Air — 620-760 kPa (90-100 psi),
2.83 liters/sec (6 scfm)
Wire Sensor — Gold plated contacts
with laser etched target
For more information, request
Catalog 1309085.
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
2
2
]
- 2.0 mm
2
]
3
/s]
3
2
/s] when required for
(32-14 AWG) (30-
5175
5