TLE52052GNT Infineon Technologies, TLE52052GNT Datasheet
TLE52052GNT
Specifications of TLE52052GNT
Related parts for TLE52052GNT
TLE52052GNT Summary of contents
Page 1
H-Bridge for DC-Motor Applications 1 Overview 1.1 Features • Delivers continuous 6 A peak current • Optimized for DC motor management applications • Operates at supply voltages typ. 200 mΩ ...
Page 2
Pin Configuration (top view) TLE 5205 GND V OUT1 IN1 IN2 AEP01990 TLE 5205- OUT1 IN1 IN2 EF GND V S AEP01991 Figure 1 Pin Assigments ...
Page 3
Pin Definitions and Functions Pin No. Pin No. Symbol P-TO220 P-DSO 1 7 OUT1 IN1 4 1, 10, GND 11 IN2 OUT2 – ...
Page 4
Functional Block Diagram 2 EF Diagnosis and Protection Circuit 1 3 IN1 5 IN2 Diagnosis and Protection Circuit 2 Figure 2 Block Diagram Data Sheet Error Flag IN OUT ...
Page 5
Circuit Description Input Circuit The control inputs consist of TTL/CMOS-compatible schmitt-triggers with hysteresis. Buffer amplifiers are driven by this stages. Output Stages The output stages consist of a DMOS H-bridge. Integrated circuits protect the outputs against short-circuit to ground ...
Page 6
Monitoring Functions Undervoltage lockout (UVLO): V When reaches the switch on voltage S All output transistors are switched off if the supply voltage V value S OFF. 1.8 Protective Function Various errors like short-circuit to + result in turn-OFF ...
Page 7
V EH Figure 3 Simplified Schematic for Open Load Detection Data Sheet Pull UP Ω Pull V Down = EL Ω TLE 5205-2 Overview EF µ & AES02395 Rev. 1.1, ...
Page 8
Diagnosis Various errors as listed in the table “Diagnosis” are detected. Short circuits and overload result in turning off the output stages after a delay simultaneously [EF = L]. Changing the inputs to a state where the fault is ...
Page 9
Electrical Characteristics 3.1 Absolute Maximum Ratings – 40 °C < < 150 ° Parameter Voltages Supply voltage Logic input voltage Diagnostics output voltage Currents of DMOS-Transistors and Freewheeling Diodes Output current (cont.) Output current (peak) Output current ...
Page 10
Operating Range Parameter Supply voltage Supply voltage increasing Supply voltage decreasing Logic input voltage Junction temperature 3.3 Electrical Characteristics < < IN1 = IN2 = HIGH (No load); – 40 ...
Page 11
Electrical Characteristics (cont’ < < IN1 = IN2 = HIGH (No load); – 40 °C < I OUT1, 2 Parameter Outputs OUT1, 2 Static Drain-Source-On Resistance Source I = – ...
Page 12
Electrical Characteristics (cont’ < < IN1 = IN2 = HIGH (No load); – 40 °C < I OUT1, 2 Parameter Short Circuit Current Limitation Source current Sink current Open Circuit ...
Page 13
Electrical Characteristics (cont’ < < IN1 = IN2 = HIGH (No load); – 40 °C < I OUT1, 2 Parameter Output Switching Times (Device Active for Source ON Sink ON ...
Page 14
Electrical Characteristics (cont’ < < IN1 = IN2 = HIGH (No load); – 40 °C < I OUT1, 2 Parameter Error Flag Output EF Low output voltage Leakage current Thermal ...
Page 15
EF Ι IN1 Ι IN2 IN1 V IN2 Figure 4 Test Circuit Overcurrent I I OUT SD Data Sheet Ι Ι 470 nF 6 Ι OUT1 3 TLE ...
Page 16
Ι OUT Source Ι OUT Sink Figure 5 Switching Time Definitions + 5 V Ω µ Figure 6 Application Circuit Data Sheet 50% t dONH 80% ...
Page 17
IN1, 2 Ι SCH Ι SDH Ι OUT1 Ι OUT1, 2 Short SCH t dSD EF Figure 7 Timing Diagram for Output Shorted to Ground IN1, 2 Ι SCL Ι SDL Ι OUT1 OUT1, ...
Page 18
Diagrams I Quiescent Current (Active) S versus Junction Temperature 7 mA Ι - Input Switching Thresholds versus Junction Temperature 3 INH, L INH 2.5 2.0 V INL 1.5 1.0 ...
Page 19
Overcurrent Shutdown Threshold versus Junction Temperature 12 Ι Low Side Transistor 8 High Side Transistor - Error-Flag Saturation Output Voltage V versus Junction Temperature EF 0 0.5 0.4 0.3 0.2 ...
Page 20
Package Outlines PG-TO220-7-11 (Plastic Transistor Single Outline Package) 0...0.3 0...0.15 1) Typical Metal surface min. X=7.25, Y=12.3 All metal surfaces tin plated, except area of cut. Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly ...
Page 21
PG-DSO-20-37 (Plastic Dual Small Outline Package) 1.2 -0.3 1.27 +0.13 0 Index Marking 1 x 45˚ 15.9 1) Does not include plastic or metal protrusion of 0.15 max. per side Green Product (RoHS compliant) To meet the world-wide ...
Page 22
PG-TO263-7-1 (Plastic Transistor Single Outline Package) 0...0.3 7x0.6 1) Typical Metal surface min. X=7.25, Y=6.9 All metal surfaces tin plated, except area of cut. Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to ...
Page 23
PG-TO220-7-12 (Plastic Transistor Single Outline Package) 0...0.15 1) Typical Metal surface min. X=7.25, Y=12.3 All metal surfaces tin plated, except area of cut. Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be ...
Page 24
Revision History Version Date Rev. 1.1 2007-07-31 RoHS-compliant version of the TLE 5205-2 Data Sheet Changes • All pages: Infineon logo updated • Page 1: “AEC qualified” and “RoHS” logo added, “Green Product (RoHS compliant)” and “AEC qualified” statement ...
Page 25
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...