CMB02070X2700GB200 Vishay, CMB02070X2700GB200 Datasheet - Page 4

• Manufacturer Part Number: CMB02070X2700GB200
• Description: Res Carbon Film 2309 270 Ohm 2% 2/5W Molded Melf SMD Blister T/R
• Manufacturer: Vishay
• Type: Carbon Filmr
• Series: CMBr

Specifications of CMB02070X2700GB200

• Case Size: 2309
• Resistance Value: 270 Ohm
• Power Rating: 2/5 W
• Tolerance: 2 %
• Resistance (ohms): 270
• Power (watts): 1W
• Composition: Carbon Film
• Features: Pulse Withstanding
• Size / Dimension: 0.087" Dia x 0.228" L (2.20mm x 5.80mm)
• Lead Style: Surface Mount (SMD - SMT)
• Package / Case: MELF, 0207
• Resistance In Ohms: 270
• Case: 0207
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Temperature Coefficient: -
• Height: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: CMB-270TR

CMB 0207
Vishay Beyschlag
DESCRIPTION
Production of the CMB 0207 specialty MELF resistor is
strictly controlled and follows an extensive set of instructions
established for reproducibility. A homogeneous and dense
carbon film is deposited on a high grade ceramic body
(Al
pressed on the coated rods. Products with a resistance of
15 Ω or lower are made without trimming, whereas a special
laser is used to achieve a target value of 16 Ω or above
by smoothly cutting a helical groove in the resistive layer
without damaging the ceramics. The resistor elements are
covered by a protective coating designed for electrical,
mechanical and climatic protection. The terminations receive
a final pure tin on nickel plating. Four color code rings
designate the resistance value and tolerance in accordance
with IEC 60 062
The result of the determined production is verified by an
extensive testing procedure performed on 100 % of the
individual resistors. Only accepted products are laid directly
into the blister tape in accordance with IEC 60 286-3
ASSEMBLY
The resistors are suitable for processing on automatic
SMD assembly systems. They are suitable for automatic
soldering using wave, reflow or vapour phase as shown in
IEC 61760-1
cleaning solvents commonly used in the electronics
industry, including alcohols, esters and aqueous solutions.
The suitablility of conformal coatings, if applied, shall be
qualified by appropiate means to ensure the long-term
stability of the whole system. The resistors are RoHS
compliant, the pure tin plating provides compatibility with
lead (Pb)-free and lead containing soldering processes. The
immunity of the plating against tin whisker growth has been
proven under extensive testing.
All products comply with the GADSL
CEFIC-EECA-EICTA
hazardous substances. This includes full compliance with
the following directives:
• 2000/53/EC End of Vehicle life Directive (ELV) and
• 2002/95/EC Restriction of the use of Hazardous
• 2002/96/EC Waste Electrical and Electronic Equipment
Solderability is specified for 2 years after production or
requalification. The permitted storage time is 20 years.
Notes
(1)
(2)
(3)
www.vishay.com
70
Annex II (ELV II)
Substances Directive (RoHS)
Directive (WEEE)
2
Global Automotive Declarable Substance List, see www.gadsl.org.
CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association), EICTA (European trade
organisation representing the information and communications technology and consumer electronics), see
→ issues → environment policy → chemicals → chemicals for electronics.
The quoted IEC standards are also released as EN standards with the same number and identical contents.
O
3
). Nickel plated steel termination caps are firmly
(3)
(3)
. The encapsulation is resistant to all
.
(2)
list of legal restrictions on
For technical questions, contact:
(1)
High Pulse Load MELF Resistors
and the
(3)
.
APPROVALS
Where applicable the resistors are tested in accordance with
EN 140401-803 which refers to EN 60115-1, EN 140400 and
the variety of environmental test procedures of the
IEC 60068
Vishay
Manufacturer” in accordance with IEC QC 001002-3,
clause 2. The release certificate for “Technology Approval
Schedule” in accordance with CECC 240001 based on
IEC QC 001002-3, clause 6 is granted for the Vishay
BEYSCHLAG manufacturing process.
[e-mail]
BEYSCHLAG
(3)
series.
has
www.eicta.org/index.php?id=995
achieved
Document Number: 28755
Revision: 01-Mar-10
“Approval
of