MCT06030D1500BP 500 Vishay, MCT06030D1500BP 500 Datasheet - Page 6

• Manufacturer Part Number: MCT06030D1500BP 500
• Description: Res Thin Film 0603 150 Ohm 0.1% 1/10W ±25ppm/°C Molded SMD Paper T/R
• Manufacturer: Vishay
• Type: Thin Filmr

Specifications of MCT06030D1500BP 500

• Case Size: 0603
• Resistance Value: 150 Ohm
• Power Rating: 1/10 W
• Tolerance: 0.1 %

TEST AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
EN 60115-1, generic specification (includes tests)
EN 140400, sectional specification (includes schedule for
qualification approval)
EN 140401-801, detail specification (includes schedule for
conformance inspection)
The components are approved in accordance with the
European CECC-system, where applicable. The following
table contains only the most important tests. For the full test
schedule refer to the documents listed above. The testing
also covers most of the requirements specified by
EIA/IS-703 and JIS-C-5202.
The tests are carried out in accordance with IEC 60068 and
under standard atmospheric conditions in accordance with
Document Number: 28700
Revision: 18-Dec-09
TEST PROCEDURES AND REQUIREMENTS
4.5
4.8.4.2
4.25.1
4.25.3
4.24
CLAUSE
60115-1
EN
METHOD
78 (Cab)
60068-2
TEST
IEC
-
-
-
-
-
MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision
operation mode
operation mode
upper category
Endurance at
Endurance at
Endurance at
Temperature
temperature
steady state
Damp heat,
Resistance
coefficient
Precision
Standard
70 °C:
70 °C:
TEST
For technical questions, contact:
Precision Thin Film Chip Resistors
whichever is the less severe;
whichever is the less severe;
U =
U =
Stability for product types:
At (20/- 10/20) °C and
(40 ± 2) °C; 56 days;
1.5 h on; 0.5 h off;
1.5 h on; 0.5 h off;
P
P
PROCEDURE
125 °C; 1000 h
(93 ± 3) % RH
85 °C; 1000 h
70 °C; 1000 h
70 °C; 8000 h
70 °C; 1000 h
70 °C; 8000 h
(20/85/20) °C
70
70
x R
x R
or U = U
or U = U
MCU 0805
MCA 1206
MCS 0402
MCT 0603
max.
max.
IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated
temperature range: Lower Category Temperature, Upper
Category Temperature; damp heat, long term, 56 days) is
valid. Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
The components are mounted for testing on boards in
accordance with EN 60115-1, 4.31 unless otherwise
specified.
The parameters stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN 140401-801. However, some
additional tests and a number of improvements against those
minimum requirements have been included.
[e-mail]
;
;
STABILITY CLASS 0.1
± (0.1 % R + 0.02 Ω)
± (0.2 % R + 0.02 Ω)
± (0.1 % R + 0.02 Ω)
100 Ω to 47.5 kΩ
470 Ω to 10 kΩ
100 Ω to 10 kΩ
47 Ω to 332 kΩ
± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
PERMISSIBLE CHANGE (ΔR)
± (0.1 % R + 0.02 Ω)
± (0.2 % R + 0.02 Ω)
± (0.2 % R + 0.02 Ω)
± (0.4 % R + 0.05 Ω)
± 0.1 % R; ± 0.25 % R
REQUIREMENTS
Vishay Beyschlag
STABILITY CLASS 0.25
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (0.2 % R + 0.02 Ω)
> 47.5 kΩ to 1.5 MΩ
> 10 kΩ to 52.3 kΩ
> 10 kΩ to 511 kΩ
> 332 kΩ to 2 MΩ
39 Ω to < 100 Ω;
39 Ω to < 100 Ω;
39 Ω to < 47 Ω;
(1)
(1)
(1)
(1)
www.vishay.com
213