1055478-1 TE Connectivity, 1055478-1 Datasheet - Page 41

• Manufacturer Part Number: 1055478-1
• Description: Connector Accessories Cable Bender
• Manufacturer: TE Connectivity
• Type: Benderr

Specifications of 1055478-1

• Lead Free Status / RoHS Status: RoHS Not Applicable

Specifications
General
Materials and Finishes
Housings and Center Contacts
Dielectric
Shrouds
Hermetic Seal
Electrical
Frequency Range
VSWR
Voltage Rating
Insertion Loss
Insulation Resistance
Dielectric Withstanding Voltage
RF High Potential
Impedance
RF Leakage
Contact Resistance
Mechanical
Durability
Radial Misalignment
Axial Misalignment
Force to Engage
Force to Disengage
Center Contact Retention
Environmental
Operating Temperature
Vibration
Shock
Thermal Shock
Moisture Resistance
Interface Dimensions
Catalog 1308940
Revised 5-03
www.tycoelectronics.com
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
OSMP Microminiature Push-On
Coaxial Connectors
Introduction
Jack
Note: The U.S. Government (DSCC) has determined that the above specified interface dimensions are interchangeable
and intermateble with Gilbert GPO Series RF Connectors.
Anti-Rock Ring
[3.70]
.145
EMI Ring
Bullet
Dia.
Max.
(Continued)
[3.40]
.132
Min.
[2.80]
Beryllium Copper per ASTM-B-196; gold plate over nickel plate
PTFE Fluorocarbon per ASTM-D-1457
Stainless steel per ASTM-A582 Type 303; passivate per ASTM-A380
Glass bead
dc - 40.0 GHz
1.10:1 Maximum dc - 23.0 GHz
1.15:1 Maximum 23.0 - 26.0 GHz
1.40:1 Maximum 26.0 - 40.0 GHz
335 Vrms maximum at sea level
0.10 f (GHz) maximum
5000 megohms minimum
500 volts (VRMS minimum)
325 volts (VRMS minimum) @ 5 MHz
50 ohms nominal
-80dB to 3 GHz, -65dB from 3 to 26.5 dB minimum
Initial center contact 6.0 milliohms maximum
Outer contact 2.0 milliohms maximum
100 mating cycles minimum
±0.020 minimum
.000/.010
full detent
half detent
smooth bore
full detent
half detent
smooth bore
1.5 lbs. minimum axial force
-85°F to +329°F [-65°C to +165°C]
per mil-std-202, method 204, test condition D
per mil-std-202, method 213, test condition I
per mil-std-202, method 107, test condition B
per MIL-STD-202 method 106, except step 7b shall be omitted. Resistance shall be 200 megohms
within 5 minutes after removal from humidity.
.112
Min.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
[3.43]
.135
[3.43]
.135
Dia.
Max.
Dia.
Max.
15.0 lbs. maximum
10.0 lbs. maximum
2.0 lbs. maximum
5.0 lbs. minimum
2.0 lbs. minimum
0.5 lbs. minimum
Shroud
[3.20
[8.60
Smooth Bore
.125
.142
Full Detent
.002
.050
.003
.076
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
]
]
Dia.
Dia.
[2.80
.110
.002
.050
]
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
7041
7