583204-2 TE Connectivity, 583204-2 Datasheet - Page 94

• Manufacturer Part Number: 583204-2
• Description: Conn Contact F 1 POS Crimp ST Cable Mount Strip on Reel
• Manufacturer: TE Connectivity
• Type: Contactr

Specifications of 583204-2

• Number Of Contacts: 1
• Contact Plating: Gold Over Nickel
• Mounting: Cable Mount
• Termination Method: Crimp
• Rohs Compliant: YES
• Product Type: Contact
• Wire Insulation Diameter (mm [in]): 1.27 – 1.63 [0.050 – 0.064]
• Termination Method To Wire/cable: Crimp
• Contact Retention In Housing: Crimp Snap-In
• Solder Tail Contact Plating: Gold Flash
• Wire Range (mm [awg]): 0.12-0.40² [26-22]
• Contact Plating, Mating Area, Material: Gold (30)
• Contact Base Material: Phosphor Bronze
• Underplate Material: Nickel
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Wire/Cable
• Contact Packaging Method: Strip Form

Hot-Plug High Current
Modular Power Connectors
Key Features
■
■
■
■
■
■
Typical Applications
■
■
■
■
■
■
■
Catalog 1773096
Revised 2-10
www.tycoelectronics.com
Modular construction
Blind-mating
High current CROWN BAND
contacts
Logic/Signal
Locking system
Uses ELCON drawer
contacts
Power Supplies
Telecommunications
Automatic Test Equipment
Computer Hardware
Process Control
Uninterruptible Power
Systems
All Domino products in
this section are RoHS
compliant
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Power Connectors & Interconnection Systems
Domino Series Connectors
The ELCON Domino
connector system is a
modular high-current
connector system consisting
of interchangeable modules
which can provide AC,
DC, logic and signal,
float mounting, and pin
sequencing. All Domino
modules incorporate
CROWN BAND technolo-
gies, tried and tested under
the most arduous conditions.
The high current capabilities
virtually eliminate the need
for bussing or splitting
current, with resulting space
savings and economies.
The Domino connector
system allows the user to
configure a connector
specific to an application,
from off-the-shelf
components. It can be
purchased as separate
modules and assembled
by the user, but is more
generally ordered as a
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
connector assembly using
an assembly part number
which Tyco Electronics
assigns to a specific
configuration. Consult
Tyco Electronics for
assistance in laying out a
new connector. If required,
Domino connector
assembly is simple: once
the locking rails are cut to
size, the only tool required
is a Phillips screwdriver for
tightening the end-caps.
Most Domino contacts
are the same as used in
ELCON drawer connectors.
Modules A through E and R
are sold as housings with
retention clips; the contacts
are ordered separately.
See page 80 for available
contact options and plating
information, page 67 for
tooling. Modules K, L, and
M are sold pre-loaded
with contacts. Domino
assemblies are shipped
complete with contacts.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
The Domino system is ideal
for use with hot-pluggable
power supplies of the type
employed for load-sharing
and/or redundant power for
computer systems. Current
interruption capability is
standard in the L module
and an available option in
the A module.
The CROWN BAND contact
is a small louvered cylindri-
cal receptacle of beryllium
copper. Manufactured on
progressive dies to allow
consistent, even insertion
and withdrawal forces,
its design helps ensure
maximum surface contact
area for minimum voltage
drop and minimum heat
generation. CROWN BAND
contacts also provide excel-
lent shock and vibration
resistance.
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-(0)8002-67666
155