8-215570-0 TE Connectivity, 8-215570-0 Datasheet - Page 2

• Manufacturer Part Number: 8-215570-0
• Description: Conn IDC Connector M 10 POS 2.54mm IDT RA Cable Mount Box
• Manufacturer: TE Connectivity
• Type: IDC Connectorr
• Series: Micro-MaTchr

Specifications of 8-215570-0

• Pitch: 2.54 mm
• Number Of Rows: 2
• Number Of Contacts: 10
• Gender: M
• Contact Plating: Tin Over Nickel
• Termination Method: IDT
• Connector Type: Wire To Board
• Contact Termination: IDC / IDT
• No. Of Contacts: 10
• Pitch Spacing: 1.27mm
• Colour: Red
• Connector Mounting: RoHS Compliant
• Product Type: Connector
• Type Of Connector: Paddleboard Connector
• Mount Angle: Vertical
• Pcb Mount Style: Through Hole
• Insulation Diameter (mm [in]): 0.90 [.035]
• Polarization: With
• Number Of Positions: 10
• Wire Range (mm [awg]): 0.08-0.09² [28]
• Centerline (mm [in]): 1.27 [0.050]
• Contact Base Material: Phosphor Bronze
• Contact Plating, Mating Area, Material: Tin
• Housing Color: Red
• Housing Material: Polyester GF
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Printed Circuit Board
• Packaging Method: Box
• Packaging Quantity: 250

.
2.2
DIN 17662
DIN 17670
2.3
I.E.C. 512
I.E.C 68
2.4
RCX-0102/101,102: Test methods of soldering of Surface Mount Devices
3.
3.1
Products shall be of design, construction and physical dimensions as specified on the applicable product
drawings.
All connector types of the Micro-MaTch Miniature connector System are available from 4 to 20 positions
(only even numbers )
Centerline distance between contacts is 1,27 mm (0,50”) or a multiple of this case of selectively loaded
connectors, which are available for all versions.
3.2
Contacts:
Housings:
3.3
The system consists of the following connector types:
3.3.1
Top entry and side entry, consisting of a number of contact springs, press-fit in moulded housings
3.3.2
Top entry/Surface Mount Compatible (SMC) consisting of a number of contact springs, press-fit in a
moulded housing. The connector is inserted into the PC board after the soldering operation and contacts
the PC board surface by means of an additional spring member with an extremely sharp tip. For firm
retention of the connector in the PC board each individual contact features a compliant pin section fitting
in the corresponding hole.
Rev. F
R6-77 (Rev. 07-01)
PRODUCT DESCRIPTION
Female-on-board connector
Female-on-board connector
DIN-specifications.
I.E.C. Specifications
EIAJ Specification.
Design and Construction:
Material and Finish:
Connector types
Wrought copper alloys (tin-bronze); chemical composition
Plate, sheet and strip of wrought copper an copper alloys: mechanical properties
Connectors used for frequencies below 3 MHz (Mc/s)
Basic environmental testing procedures for electric components and electronic
equipment.
Phosphor Bronze according DIN specifications, tinplated over nickel underlayer.
General: Polyester (PBT) 20% Glass filled
SMD-versions:P.A.4.6;30% Glassfilled
UL 94 V-0 rated
Colour: Red
EC EH1O-XXXX-05
108-19052
Page 2 of 15