PQ24050QGA20NNS SYNQOR, PQ24050QGA20NNS Datasheet
PQ24050QGA20NNS
Specifications of PQ24050QGA20NNS
Related parts for PQ24050QGA20NNS
PQ24050QGA20NNS Summary of contents
Page 1
... UL/cUL 60950-1 recognized (US & Canada), basic insulation rating • TUV certified to EN60950-1 • Meets 72/23/EEC and 93/68/EEC directives which facilitates CE Marking in user’s end product • Board and plastic components meet UL94V-0 flamma- bility requirements • NEBS and ETSI compliant www.synqor.com T echnical T echnical S pecification S ...
Page 2
... TRIM 7 SENSE(+) 8 Vout(+) Notes: 1. SENSE(-) should be connected to Vout(-) either remotely or at the converter. 2. Leave TRIM pin open for nominal output voltage. 3. SENSE(+) should be connected to Vout(-) either remotely or at the converter. www.synqor.com Doc.# 005-2QG233D Rev. B 18-36 V Input: 18-36 V Input: 3.3 V Output: Output: 3 ...
Page 3
... Isolation Voltage (dielectric strength) Isolation Resistance 2 Isolation Capacitance Note 1: For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Higher values of isolation capacitance can be added external to the module. Product # PQ24033QGA25 Phone 1-888-567-9596 =24Vdc unless otherwise noted; full operating temperature range is -40°C to +100°C ambient Min ...
Page 4
... EN60950-1 72/23/EEC 93/68/EEC Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 GR-1089-CORE • An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website. QUALIFICATION TESTING Parameter P # Units QUALIFICATION TESTING ...
Page 5
... C (nominal input voltage). ° Figure 6: Thermal plot of converter at 20 amp load current with 55 air flowing at the rate of 200 LFM. Air is flowing across the converter from input to output (nominal input voltage). www.synqor.com 18-36 V Input: 18-36 V Input: 3.3 V Output: Output: 3 Current: ...
Page 6
... Figure 10: Turn-on transient at zero load (2 ms/div Vout (1V/div ON/OFF input (5V/div) Ω Figure 12 ESR tantalum capac- 50% of Iout(max): dI/dt = 5A/µs). Load cap: 470µ capacitor and 1µF ceramic cap Vout (100mV/div Iout (10A/div). www.synqor.com 18-36 V Input: 18-36 V Input: 3.3 V Output: Output: 3 ...
Page 7
... Bandwidth: 20 MHz. See Figure 13 Figure 18: Load current (10A/div function of time when the con- verter attempts to turn on into a 10 mΩ short circuit. Top trace (2.5ms/div expansion of the on-time portion of the bottom trace. www.synqor.com 18-36 V Input: 18-36 V Input: 3.3 V Output: Output: 3 ...
Page 8
... Vin 18 Vin 24 Vin 24 Vin 36 Vin 36 Vin 0.1 10 10,000 100,000 Figure 22: Magnitude of incremental input impedance ( for minimum, nominal, and maximum input voltage at full rated power. www.synqor.com Doc.# 005-2QG233D Rev. B 18-36 V Input: 18-36 V Input: 3.3 V Output: Output: 3 Current: Current (82.5W) (82.5W) ...
Page 9
... Note: the output over-voltage protection circuit senses the voltage ON/OFF ON/OFF Vin( _ Vin Positive Logic (Permanently Enabled) 5V TTL/ ON/OFF CMOS Vin Direct Logic Drive www.synqor.com 18-36 V Input: 18-36 V Input: 3.3 V Output: Output: 3 Current: Current Quarter-brick P ackage: P ...
Page 10
... Vout when the temperature at the sensed location reaches the Over- Temperature Shutdown value. It will allow the converter to turn on again when the temperature of the sensed location falls by the amount of the Over-Temperature Shutdown Restart Hysteresis value. www.synqor.com 18-36 V Input: 18-36 V Input: 3.3 V ...
Page 11
... Input System Instability: This condition can occur because any DC/DC converter appears incrementally as a negative resistance load. A detailed application note titled “Input System Instability” is available on the SynQor web site (www.synqor.com) which provides an understanding of why this instability arises, and shows the preferred solution for cor- recting it ...
Page 12
... Substances) Directive bans the use of Lead, Cadmium, Hexavalent Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor product is available as 5/6 RoHS compliant (product with lead) or 6/6 RoHS compliant. For more information please refer to SynQor’s RoHS addendum available at our RoHS Compliance / Lead Free Initiative web page or e-mail us at rohs@synqor ...
Page 13
... SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor ...