LT4HW-AC24VS Panasonic Electric Works, LT4HW-AC24VS Datasheet - Page 2

• Manufacturer Part Number: LT4HW-AC24VS
• Manufacturer: Panasonic Electric Works

Specifications of LT4HW-AC24VS

• Lead Free Status / RoHS Status: Compliant

LT4H-W
Specifications
Applicable standard
Item
Rating
Time
accuracy
(max.)
Contact
Life
Electrical
Mechanical
Operating
conditions
Connection
Protective construction
EMC
Safety standard
Rated operating voltage
Rated frequency
Rated power consumption
Rated control capacity
Time range
Time counting direction
Operation mode
Start/Reset/Stop input
Lock input
Input signal
Indication
Power failure memory
method
Operating time fluctuation
Temperature error
Voltage error
Setting error
Contact arrangement
Contact resistance (Initial value)
Contact material
Mechanical (contact)
Electrical (contact)
Allowable operating voltage range
Breakdown voltage
(Initial value)
Insulation resistance
(Initial value)
Operating voltage reset
time
Temperature rise
Vibration
resistance
Shock
resistance
Ambient temperature
Ambient humidity
Air pressure
Ripple rate
(EMI)EN61000-6-4
Radiation interference electric field strength
Noise terminal voltage
(EMS)EN61000-6-2
Static discharge immunity
RF electromagnetic field immunity
EFT/B immunity
Surge immunity
Conductivity noise immunity
Power frequency magnetic field immunity
Voltage dip/Instantaneous stop/Voltage fluctuation immunity
Functional
Destructive
Functional
Destructive
Type
(under the flow of nominal operating current at nominal voltage)
2,000 Vrms for 1 min: Between live and dead metal parts (11-pin type only)
2,000 Vrms for 1 min: Between input and output
1,000 Vrms for 1 min: Between contacts
Min. 100 M :
100 to 240 V AC, 24 V AC
Min. input signal width: 1 ms, 20 ms (2 directions by selected by DIP switch) (The 8 pin type does not have a stop input.)
EN61812-1
50/60 Hz common
Min. 2x10
Max. 10 V A
AC type
± (0.005% + 20 ms) in case of input signal start
Min. 10
± (0.005% + 50 ms) in case of power on start
—
99.99s, 999.9s, 9999s, 99min59s, 999.9min, 99h59min, 999.9h, 9999h (selected by DIP switch)
7
ope. (Except for switch operation parts)
7-segment LCD, Elapsed value (backlight red LED), Setting value (backlight yellow LED)
100 m (at 1 A 6 V DC)
5
ope. (At rated control voltage)
Timed-out 1 Form C
10 to 55 Hz: 1 cycle/ min single amplitude of 0.35 mm
Relay output type
Ag alloy/Au flash
Between live and dead metal parts
Between input and output (At 500V DC)
Between contacts
10 to 55 Hz: 1 cycle/ min single amplitude of 0.75 mm
5 A, 250 V AC
Open collector input Input impedance: Max. 1 k ; Residual voltage: Max. 2V
Max 65° C
Min. input signal width: 20 ms (The 8-pin type does not have a lock input.)
Integrating input: Delayed one shot, OFF-start flicker or ON-start flicker
Open impedance: 100 k or less, Max. energized voltage: 40 V DC
Pulse input: Delayed one shot, OFF-start flicker or ON-start flicker
09/2009
12 to 24 V DC
Min. 294 m
20 % or less
Min. 98 m
Max. 3 W
DC type
(2 directions selectable by DIP switch)
85 to 110 % of rated operating voltage
IP66 (front panel with rubber gasket)
Addition (UP)/Subtraction (DOWN)
EN55011 Group1 ClassA
EN55011 Group1 ClassA
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11 10 ms, 30% (rated voltage)
—
–10° C to 55° C
Max. 85 % RH (non-condensing)
EEP-ROM (Min. 10
8-pin/11-pin/screw terminal
321.522
964.567
860 to 1,060 h Pa
Max. 0.5 s
ft./s
ft./s
4 kV contact
8 kV air
10 V/m AM modulation (80 MHz to 1 GHz)
10 V/m pulse modulation (895 MHz to 905 MHz)
2 kV (power supply line)
1 kV (signal line)
1 kV (power line)
10 V/m AM modulation (0.15 MHz to 80 MHz)
30 A/m (50 Hz)
100 ms, 60% (rated voltage)
1,000 ms, 60% (rated voltage)
5,000 ms, 95% (rated voltage)
+14° F to +131° F
Min. 100 M :
2,000 Vrms for 1 min: Between live and dead metal parts (Pin type only)
2,000 Vrms for 1 min: Between input and output
2
Pollution Degree 2/Overvoltage Category II
2
(4 times on 3 axes)
(5 times on 3 axes)
5
100 to 240V AC, 24V AC
[
overwriting)
Operating voltage: 85% to 110%
Temperature: –10°C to +55°C
Min. input signal width: 1ms
50/60 Hz common
Max. 10 V A
AC type
Min. 10
.014 inch
Timed-out 1 Form A (Open collector)
.030 inch
—
Between live and dead metal parts
Between input and output (At 500V DC)
7
Transistor output type
ope. (At rated control voltage)
(10 min on 3 axes)
100 mA, 30 V DC
(1 h on 3 axes)
—
—
—
—
+14°F to +131°F
12 to 24 V DC
20 % or less
Max. 3 W
DC type
—
]
21