XE0092-ITR Cermetek Microelectronics, XE0092-ITR Datasheet
XE0092-ITR
Specifications of XE0092-ITR
Related parts for XE0092-ITR
XE0092-ITR Summary of contents
Page 1
... Like all our DAA's the XE0092 is a complete DAA. It includes a 2-4 wire converter, loop current holding circuit, hook switch and ring indicator. It also supports Caller ID. The XE0092 complies with FCC Part 68 rules for direct connection to the telephone line. Cermetek offers the XE0092 in three lead styles ...
Page 2
... Cermetek Microelectronics, Inc. Pin Name Description 5 /RI 11 TIP 10 RING 6 /CID /CID is an active low input to the XE0092. 7 RX- RX- is the negative half of the differential 8 RX+ RX+ is the positive half of the differential 9 GND Ground connection to the XE0092. This The 10 Ring Ring is one wire of the two-wire ...
Page 3
... If the user activates the /CID input while the XE0092 is off-hook, the Caller ID signal is passed through to the host through the RX pins on the XE0092. If the XE0092 is off-hook, /OH low, Caller ID pass-through cannot be enabled regardless of the state of /CID. ...
Page 4
... F1 and F2 prevent damage to the system when a power line crosses with the telephone line. Cermetek recommends the Raychem TR600-150 for this function. The TR600-150 is a PTC device which automatically resets after use. ©2009 Cermetek Microelectronics, Inc. Page 4 Document No. 607-0100 Revision A (10/09) XE0092 Low-cost DAA Module Cermetek ...
Page 5
... Cermetek Microelectronics, Inc XE0092 Surface-Mount PCB Layout Recommendations B C Dimensions Typical (Inches Note: No components or traces should be placed under the XE0092LCC module. ©2009 Cermetek Microelectronics, Inc 0.10 Pad Length 0.06 Pad Width 0.10 Space between adjacent pads 0.80 Distance from Pin 1 to Pin 9 ...
Page 6
... Cermetek Microelectronics, Inc XE0092 Surface-Mount Soldering Instructions The XE0092 is subject to damage if over-exposed to heat during solder reflow operations. Following the soldering instructions below will ensure that the process of soldering the module to the board does not damage the modem. Maximum Temperature Maximum Time above 235 ° C Maximum Time in reflow zone (217 ° ...
Page 7
... Hook-Switch Open Impedance XE0092 ABSOLUTE MAXIMUM RATINGS Storage Temperature Operating Temperature Range * * The XE0092 can be ordered with an Operating Temperature of -40 ° +85 ° extra cost. Products tested to the higher temperature standard will be marked as –ITR. ©2009 Cermetek Microelectronics, Inc. XE0092 ELECTRICAL SPECIFICATIONS Minimum 3 ...
Page 8
... Distance from Pin 1o to the Edge of the product 2.54 Distance between adjacent pins 1.27 Total height of the interface pin 1.27 Distance the pin extends beyond the product edge 33.02 Total distance across the product including pin spread Page 8 XE0092 Low-cost DAA Module Document No. 607-0100 Revision A (10/09) ...
Page 9
... Length of Solder Pad 10.16 Distance from Pin the Edge of the product 2.54 Distance between adjacent pins 1.27 Distance from Pin 11 to the Edge of the product 1.27 Distance from Pin 10 to the Edge of the product Page 9 XE0092 Low-cost DAA Module Document No. 607-0100 Revision A (10/09) ...
Page 10
... Distance from Pin 1o to the Edge of the product 2.54 Distance between adjacent pins 3.81 Total height of the interface pin 1.27 Distance the pin extends beyond the product edge 27.94 Distance between Pin Rows Page 10 XE0092 Low-cost DAA Module Document No. 607-0100 Revision A (10/09) ...
Page 11
... If the system is capable of DTMF dialing, the maximum DTMF transmission level must be less than 0 dBm averaged over a 3 second interval. 4. Billing Delay A delay of 2 seconds or greater is required after the time the XE0092 is taken “off hook” and before any information is transmitted. This is required to ensure that billing information may be exchanged between telephone company central offices without interference. ...
Page 12
... XE0092LCC XE0092T Low cost DAA for voice or data with through-hole leads, 0° to 70° C operation XE0092-ITR Low cost DAA for voice or data with surface-mount leads, -40° to 85° C operation XE0092LCC-ITR Low cost, Leadless DAA for voice or data, -40° to 85° C operation XE0092T-ITR Low cost DAA for voice or data with through-hole leads, -40° ...