MCP1703T-5002E/MC Microchip Technology, MCP1703T-5002E/MC Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP1703T-5002E/MC
Manufacturer Part Number
MCP1703T-5002E/MC
Description
Low Iq 250mA LDO, Vin 16V Max, Vout =5.0V 8 DFN 2x3mm T/R
Manufacturer
Microchip Technology
Datasheet
1.SOT89-3EV-VREG.pdf
(28 pages)
Specifications of MCP1703T-5002E/MC
Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 16V
Voltage - Dropout (typical)
0.33V @ 250mA
Number Of Regulators
1
Current - Output
250mA (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-DFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MCP1703T-5002E/MCTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP1703T-5002E/MC
Manufacturer:
MICROCHIP
Quantity:
12 000
MCP1703
3.0
The descriptions of the pins are listed in
TABLE 3-1:
3.1
Regulator ground. Tie GND to the negative side of the
output and the negative side of the input capacitor.
Only the LDO bias current (2.0 µA typical) flows out of
this pin; there is no high current. The LDO output
regulation is referenced to this pin. Minimize voltage
drops between this pin and the negative side of the
load.
3.2
Connect V
positive terminal of the output capacitor. The positive
side of the output capacitor should be physically
located as close to the LDO V
The current flowing out of this pin is equal to the DC
load current.
DS22049E-page 10
2, 3, 5, 6, 7
2x3 DFN-8
Pin No.
4
1
8
9
PIN DESCRIPTIONS
Ground Terminal (GND)
Regulated Output Voltage (V
OUT
to the positive side of the load and the
SOT-223-3
MCP1703 PIN FUNCTION TABLE
Pin No.
2,Tab
—
—
3
1
OUT
SOT-23A
Pin No.
pin as is practical.
—
—
1
2
3
Table
OUT
3-1.
SOT-89-3
Pin No.
2,Tab
)
—
—
1
3
Name
3.3
Connect V
Like all low dropout linear regulators, low source
impedance is necessary for the stable operation of the
LDO. The amount of capacitance required to ensure
low source impedance will depend on the proximity of
the input source capacitors or battery type. For most
applications, 1 µF of capacitance will ensure stable
operation of the LDO circuit. For applications that have
load currents below 100 mA, the input capacitance
requirement can be lowered. The type of capacitor
used can be ceramic, tantalum, or aluminum
electrolytic. The low ESR characteristics of the ceramic
will yield better noise and PSRR performance at
high-frequency.
3.4
There is an internal electrical connection between the
Exposed Thermal Pad (EP) and the V
be connected to the same potential on the Printed
Circuit Board (PCB).
V
GND
V
NC
EP
OUT
IN
Unregulated Input Voltage (V
Exposed Thermal Pad (EP)
Ground Terminal
Regulated Voltage Output
Unregulated Supply Voltage
No Connection
Exposed Thermal Pad (EP); must be
connected to VSS.
IN
to the input unregulated source voltage.
2010 Microchip Technology Inc.
Function
SS
pin; they must
IN
)