MIC29371-12WU TR Micrel Inc, MIC29371-12WU TR Datasheet - Page 5
![750mA LDO Fixed Voltage + Flag + Shutdown ( )](/photos/12/65/126560/576-to-263_sml.jpg)
MIC29371-12WU TR
Manufacturer Part Number
MIC29371-12WU TR
Description
750mA LDO Fixed Voltage + Flag + Shutdown ( )
Manufacturer
Micrel Inc
Datasheet
1.MIC2937A-3.3WU.pdf
(12 pages)
Specifications of MIC29371-12WU TR
Regulator Topology
Positive Fixed
Voltage - Output
12V
Voltage - Input
Up to 26V
Voltage - Dropout (typical)
0.37V @ 750mA
Number Of Regulators
1
Current - Output
750mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-263-5, D²Pak (5 leads + Tab), TO-263BA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MIC29371-12WUTR
MIC29371-12WUTR
MIC29371-12WUTR
MIC2937A/29371/29372
Note 1:
apply when operating the device outside of its rated operating conditions. The maximum allowable power dissipation is a function of the
maximum junction temperature, T
allowable power dissipation at any ambient temperature is calculated using: P
power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
Note 2:
Note 3:
heating effects are covered by the thermal regulation specification.
Note 4:
measured at 1V differential. At low values of programmed output voltage, the minimum input supply voltage of 4.3V over temperature must
be taken into account. The MIC2937A operates down to 2V of input at reduced output current at 25°C.
Note 5:
plus the ground pin current.
Note 6:
current with normal output voltage.
Note 7:
ing load or line regulation effects. Specifications are for a 200mA load pulse at V
Note 8:
Note 9:
measured at 6V input (for a 5V regulator). To express these thresholds in terms of output voltage change, multiply by the error amplifier
gain = V
the output drops by 95 mV x 5V/1.235 V = 384 mV. Thresholds remain constant as a percent of V
warning occurring at typically 5% below nominal, 7.7% guaranteed.
Note 10: Circuit of Figure 3 with R1 ≥ 150kΩ. V
Note 11: When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode
clamped to ground.
Note 12: Maximum positive supply voltage of 60V must be of limited duration (< 100ms) and duty cycle ( ≤ 1%). The maximum continu-
ous supply voltage is 26V.
Schematic Diagram
May 2006
OUT
Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not
Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range.
Regulation is measured at constant junction temperature using low duty cycle pulse testing. Changes in output voltage due to
Dropout Voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value
Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the load current
The MIC2937A family features fold-back current limiting. The short circuit (V
Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, exclud-
V
Comparator thresholds are expressed in terms of a voltage differential at the Adjust terminal below the nominal reference voltage
REF
/V
REF
≤ V
= (R1 + R2)/R2. For example, at a programmed output voltage of 5V, the Error output is guaranteed to go low when
OUT
≤ (V
IN
50 kΩ
10 kΩ
– 1 V), 4.3V ≤ V
Q42
Q40
J (MAX)
R30
k Ω
Q6
30
20 kΩ
50 kΩ
Q41
, the junction-to-ambient thermal resistance, θ
R2
R1
10
Q1
Q3
50 kΩ
R3
R11
18
k Ω
ERROR
180
IN
IN
R5
k Ω
≤ 26V, 5mA < I
C1
20
pF
Q13
SHUTDOWN
13 kΩ
R4
140
R6
k Ω
Q4
Q38
Q12
Q39
Q2
Q5
Q37
31.4 k Ω
27.8 k Ω
20.6
R11
R8
R9
Q15A
k Ω
R26
60 kΩ
≥ 2V and V
Q7
Q11
Q36
R10
150
k Ω
L
Q8
≤ 750 mA, T
R25
2.8 kΩ
Q9
5
Q34
IN
R12
110
k Ω
Q20
≤ 26V,V
Q18
J
R13
GND
Q16
100
k Ω
≤ T
(MAX)
R22
150 k Ω
IN
OUT
Q15B
J MAX.
Q17
= 20V (a 4W pulse) for T = 10ms.
= (T
R14
350
k Ω
C2
40 pF
= 0.
JA
, and the ambient temperature, T
J(MAX)
Q30
Q19
Q14
DENOTES CONNECTION ON
MIC2937A-xx AND MIC29371-xx
VERSIONS ONLY
OUT
Q31
Q21
– T
= 0V) current limit is less than the maximum
Q29
FEEDBACK
12 kΩ
R17
A
) / θ
R24
50 kΩ
Q28
OUT
Q22
R16
30 kΩ
JA.
R15
100 k Ω
Q25
R23 60 k Ω
R21 8 Ω
Exceeding the maximum allowable
R18
20 kΩ
as V
Q26
10Ω
R17
OUT
Q23
SHDN
MIC2937A/29371/29372
R27
R28
Q24
is varied, with the dropout
SENSE
V TAP
OUT
A
. The maximum
Micrel, Inc.