MIC2937A-12WT Micrel Inc, MIC2937A-12WT Datasheet - Page 8
![750mA LDO Fixed Volt.( )](/photos/7/55/75565/576-to-220_sml.jpg)
MIC2937A-12WT
Manufacturer Part Number
MIC2937A-12WT
Description
750mA LDO Fixed Volt.( )
Manufacturer
Micrel Inc
Datasheet
1.MIC2937A-3.3WU.pdf
(12 pages)
Specifications of MIC2937A-12WT
Regulator Topology
Positive Fixed
Voltage - Output
12V
Voltage - Input
Up to 26V
Voltage - Dropout (typical)
0.37V @ 750mA
Number Of Regulators
1
Current - Output
750mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-220-3 (Straight Leads)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
576-2233
MIC2937A-12WT
MIC2937A-12WT
MIC2937A/29371/29372
Applications Information
External Capacitors
A 10µF (or greater) capacitor is required between the MIC2937A
output and ground to prevent oscillations due to instability. Most
types of tantalum or aluminum electrolytics will be adequate;
film types will work, but are costly and therefore not recom-
mended. Many aluminum electrolytics have electrolytes that
freeze at about –30°C, so solid tantalums are recommended
for operation below –25°C. The important parameters of the
capacitor are an effective series resistance of about 5Ω or
less and a resonant frequency above 500kHz. The value of
this capacitor may be increased without limit.
At lower values of output current, less output capacitance is
required for output stability. The capacitor can be reduced to
0.5µF for current below 10mA or 0.15µF for currents below
1 mA. Adjusting the MIC29372 to voltages below 5V runs the
error amplifier at lower gains so that more output capacitance
is needed. For the worst-case situation of a 750mA load at
1.23V output (Output shorted to Adjust) a 22µF (or greater)
capacitor should be used.
The MIC2937A/29371 will remain in regulation with a minimum
load of 5mA. When setting the output voltage of the MIC29372
version with external resistors, the current through these resis-
tors may be included as a portion of the minimum load.
A 0.1µF capacitor should be placed from the input to ground
if there is more than 10 inches of wire between the input and
the AC filter capacitor or if a battery is used as the input.
Error Detection Comparator Output (MIC29371)
A logic low output will be produced by the comparator when-
ever the MIC29371 output falls out of regulation by more than
approximately 5%. This figure is the comparator’s built-in
offset of about 75mV divided by the 1.235V reference volt-
age. (Refer to the block diagram on Page 1). This trip level
remains “5% below normal” regardless of the programmed
output voltage of the MIC29371. For example, the error flag
trip level is typically 4.75V for a 5V output or 11.4V for a 12V
output. The out of regulation condition may be due either to
low input voltage,extremely high input voltage, current limit-
ing, or thermal limiting.
Figure 1 is a timing diagram depicting the ERROR signal
and the regulated output voltage as the MIC29371 input is
ramped up and down. The ERROR signal becomes valid (low)
at about 1.3V input. It goes high at about 5V input (the input
voltage at which V
voltage is load-dependent (see curve in Typical Performance
Characteristics), the input voltage trip point (about 5V) will
vary with the load current. The output voltage trip point (ap-
proximately 4.75V) does not vary with load.
MIC2937A/29371/29372
OUT
= 4.75). Since the MIC29371’s dropout
8
The error comparator has an NPN open-collector output which
requires an external pull-up resistor. Depending on system
requirements, this resistor may be returned to the 5V output
or some other supply voltage. In determining a value for this
resistor, note that while the output is rated to sink 250µA, this
sink current adds to battery drain in a low battery condition.
Suggested values range from 100k to 1MΩ. The resistor is
not required if this output is unused.
Programming the Output Voltage (MIC29372)
The MIC29372 may programmed for any output voltage be-
tween its 1.235V reference and its 26V maximum rating. An
external pair of resistors is required, as shown in Figure 3.
The complete equation for the output voltage is
where V
the Adjust pin bias current, nominally 20nA. The minimum rec-
ommended load current of 1µA forces an upper limit of 1.2MΩ
on the value of R
condition often found in CMOS in standby), I
a –2% typical error in V
temperature by trimming R
R
resistor program current to 12µA. Since the MIC29372 typically
draws 100µA at no load with SHUTDOWN open-circuited,
this is a negligible addition.
Reducing Output Noise
In reference applications it may be advantageous to reduce
the AC noise present at the output. One method is to reduce
the regulator bandwidth by increasing the size of the output
capacitor. This is relatively inefficient, as increasing the capaci-
tor from 1µF to 220µF only decreases the noise from 430µV
to 160µV
be reduced by a factor of four with the adjustable regulators
* SEE APPLICATIONS INFORMATION
2
= 100k reduces this error to 0.17% while increasing the
V
OUT
VOLTAGE
VOLTAGE
REF
= V
RMS
OUTPUT
ERROR NOT
INPUT
is the nominal 1.235 reference voltage and I
REF
for a 100kHz bandwidth at 5V output. Noise can
Figure 1. ERROR Output Timing
x { 1 + R
2
VALID
, if the regulator must work with no load (a
4.75V
*
OUT
1.3V
1
/R
which may be eliminated at room
1
. For better accuracy, choosing
2
5V
} –
|
I
FB
|
R
1
VALID
NOT
FB
*
will produce
Micrel, Inc.
May 2006
FB
is