MIC5259-2.8YML TR Micrel Inc, MIC5259-2.8YML TR Datasheet - Page 9
![IC,VOLT REGULATOR,FIXED,+2.8V,CMOS,LLCC,6PIN,PLASTIC](/photos/7/47/74764/576-6-mlf_sml.jpg)
MIC5259-2.8YML TR
Manufacturer Part Number
MIC5259-2.8YML TR
Description
IC,VOLT REGULATOR,FIXED,+2.8V,CMOS,LLCC,6PIN,PLASTIC
Manufacturer
Micrel Inc
Datasheet
1.MIC5259-2.5YD5_TR.pdf
(11 pages)
Specifications of MIC5259-2.8YML TR
Regulator Topology
Positive Fixed
Voltage - Output
2.8V
Voltage - Input
Up to 6V
Voltage - Dropout (typical)
0.3V @ 300mA
Number Of Regulators
1
Current - Output
300mA
Current - Limit (min)
350mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
6-MLF®, QFN
Voltage Regulator Type
Linear
Topology
LDO
Regulator Output Type
Fixed
Polarity Type
Positive
Number Of Outputs
Single
Input Voltage (min)
2.7V
Input Voltage (max)
6V
Output Voltage
2.8V
Package Type
MLF
Output Current
300mA
Load Regulation
0.6%
Line Regulation
0.3%/V
Output Voltage Accuracy
±1.5%
Operating Temp Range
-40C to 125C
Operating Temperature Classification
Automotive
Dropout Voltage@current (max)
0.5@300mA
Dropout Voltage@current (typ)
0.15@150mA/0.3@300mA
Pin Count
6
Mounting
Surface Mount
Quiescent Current (max)
150uA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MIC5259-2.8YMLTR
MIC5259-2.8YMLTR
MIC5259-2.8YMLTR
The actual power dissipation of the regulator circuit can
be determined using the equation:
Substituting P
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit.
For example, when operating the MIC5259-2.8BML at
70°C with a minimum footprint layout, the maximum
input voltage for a set output current can be determined
as follows:
Micrel, Inc.
September 2006
P
P
P
D
D(max)
D(max)
= (V
D(max)
= 611mW
IN
=
– V
⎛
⎜
⎝
125
for P
OUT
90
°
C
) I
°
D
C/W
−
OUT
and solving for the operating
70
+ V
°
C
⎞
⎟
⎠
IN
I
GND
9
The junction-to-ambient thermal resistance for the
minimum footprint is 90°C/W, from Table 1. The
maximum power dissipation must not be exceeded for
proper operation. Using the output voltage of 2.8V and
an output current of 200mA, the maximum input voltage
can be determined. Because this device is CMOS and
the ground current is typically 110µA over the load
range, the power dissipation contributed by the ground
current is < 1% and can be ignored for this calculation.
Therefore, a 2.8V application at 200mA of output current
can accept a maximum input voltage of 5.85V in an MLF
package. For a full discussion of heat sinking and
thermal effects on voltage regulators, refer to the
“Regulator Thermals” section of Micrel’s Designing with
Low-Dropout Voltage Regulators handbook.
611mW = (V
611mW = V
1171mW = V
V
IN(max)
= 5.85V
IN
IN
IN
× 200mA – 560mW
– 2.8V) 200mA
× 200mA
M9999-091406
MIC5259