REF195GRU-REEL7 Analog Devices Inc, REF195GRU-REEL7 Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
REF195GRU-REEL7
Manufacturer Part Number
REF195GRU-REEL7
Description
IC,VOLT REFERENCE,FIXED,5V,BICMOS,TSSOP,8PIN,PLASTIC
Manufacturer
Analog Devices Inc
Series
REF19r
Datasheet
1.REF195GPZ.pdf
(28 pages)
Specifications of REF195GRU-REEL7
Rohs Status
RoHS non-compliant
Reference Type
Series
Voltage - Output
5V
Tolerance
±10mV
Temperature Coefficient
25ppm/°C
Voltage - Input
3 ~ 15 V
Number Of Channels
1
Current - Quiescent
45µA
Current - Output
30mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-TSSOP
Current - Cathode
-
Lead Free Status / RoHS Status
REF19x Series
Using dissimilar REF19x series devices with this configuration
allows logic selection between the U1/U2-specified terminal
voltages. For example, with U1 (a REF195) and U2 (a REF196),
as noted in the table in Figure 30, changing the CMOS-compatible
V
output of 5.0 V and 3.3 V, and vice versa. Other REF19x family
units can also be used for U1/U2, with similar operation in a
logic sense, but with outputs as per the individual paired devices
(see the table in Figure 30). Of course, the exact output voltage
tolerance, drift, and overall quality of the reference voltage is
consistent with the grade of individual U1 and U2 devices.
Due to the nature of the wire-OR, one application caveat should
be understood about this circuit. Because U1 and U2 can only
source current effectively, negative going output voltage changes,
which require the sinking of current, necessarily take longer than
positive going changes. In practice, this means that the circuit is
quite fast when undergoing a transition from 3.3 V to 5 V, but the
transition from 5 V to 3.3 V takes longer. Exactly how much
longer is a function of the load resistance, R
the typical 1 μF value of C2. In general, a conservative transition
time is approximately several milliseconds for load resistances
in the range of 100 Ω to 1 kΩ. Note that for highest accuracy at
the new output voltage, several time constants should be allowed
(for example, >7.6 time constants for <1/2 LSB error @ 10 bits).
KELVIN CONNECTIONS
In many portable applications where the PCB cost and area go
hand-in-hand, circuit interconnects are very often narrow. These
narrow lines can cause large voltage drops if the voltage reference is
required to provide load currents to various functions. The inter-
connections of a circuit can exhibit a typical line resistance of
0.45 mΩ/square (for example, 1 oz. Cu).
In applications where these devices are configured as low dropout
voltage regulators, these wiring voltage drops can become a large
source of error. To circumvent this problem, force and sense
connections can be made to the reference through the use of an
operational amplifier, as shown in Figure 31. This method provides
a means by which the effects of wiring resistance voltage drops can
be eliminated. Load currents flowing through wiring resistance
produce an I-R error (I
Kelvin connection overcomes the problem by including the
wiring resistance within the forcing loop of the op amp. Because
the op amp senses the load voltage, op amp loop control forces
the output to compensate for the wiring error and to produce
the correct voltage at the load. Depending on the reference
device chosen, operational amplifiers that can be used in this
application are the OP295, OP292, and OP183.
C
logic control voltage from high to low selects between a nominal
LOAD
× R
WIRE
) at the load. However, the
L
, seen at the output and
Rev. K | Page 24 of 28
FAIL-SAFE 5 V REFERENCE
Some critical applications require a reference voltage to be
maintained at a constant voltage, even with a loss of primary
power. The low standby power of the REF19x series and the
switched output capability allow a fail-safe reference con-
figuration to be implemented rather easily. This reference
maintains a tight output voltage tolerance for either a primary
power source (ac line derived) or a standby (battery derived)
power source, automatically switching between the two as the
power conditions change.
The circuit in Figure 32 illustrates this concept, which borrows
from the switched output idea of Figure 30, again using the
REF19x device family output wire-OR capability. In this case,
because a constant 5 V reference voltage is desired for all condi-
tions, two REF195 devices are used for U1 and U2, with their
on/off switching controlled by the presence or absence of the
primary dc supply source, V
source that supplies power to the load only when V
normal (V
(maximum) standby current drain of U1 in its off state.
In operation, it is assumed that for all conditions, either U1 or
U2 is on, and a 5 V reference output is available. With this
voltage constant, a scaled down version is applied to the
Comparator IC U3, providing a fixed 0.5 V input to the negative
input for all power conditions. The R1 to R2 divider provides a
signal to the U3 positive input proportionally to V
switches U3 and U1/U2, dependent upon the absolute level of
V
with hysteresis, which provides clean, noise-free output
switching. This hysteresis is important to eliminate rapid
switching at the threshold due to V
device chosen is the AD820, a rail-to-rail output device. This
device provides high and low output states within a few mV of
V
for all V
hysteresis, changing the threshold at the positive input as a
function of the output of U3.
S
S
. In Figure 32, Op Amp U3 is configured as a comparator
, ground for accurate thresholds, and compatible drive for U2
SLEEP
Figure 31. Low Dropout, Kelvin-Connected Voltage Reference
S
conditions. R3 provides positive feedback for circuit
S
present) power conditions, V
3
REF19x
GND
OUTPUT
V
V
2
4
S
S
6
S
. V
1µF
BAT
100kΩ
is a 6 V battery backup
S
2
3
ripple. Furthermore, the
A1
V
A1 = 1/2 OP295
S
BAT
1/2 OP292
OP183
1
sees only the 15 μA
R
R
LW
LW
S
, which
S
fails. For
+V
FORCE
R
+V
SENSE
L
OUT
OUT