TBF-2012-245-R1 Susumu, TBF-2012-245-R1 Datasheet - Page 4
![FILTER BAND PASS BLUETOOTH 0805](/photos/6/13/61369/tbf-2012-245-r1_sml.jpg)
TBF-2012-245-R1
Manufacturer Part Number
TBF-2012-245-R1
Description
FILTER BAND PASS BLUETOOTH 0805
Manufacturer
Susumu
Datasheet
1.TBF-2012-245-R1.pdf
(7 pages)
Specifications of TBF-2012-245-R1
Center / Cutoff Frequency
2.45GHz
Filter Type
Bandpass
Impedance
50 Ohm
Attenuation Value
30dB @ 7.2GHz ~ 7.5GHz
Package / Case
0805 (2012 Metric)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage
-
Capacitance
-
Other names
408-1301-2
UNLESS OTHERWISE SPECIFIED
TOLERANCES ON ﹕
X
X.X
X.XX
ANGLES ± HOLE DIA. ±
TITLE :
7. Reliability Test
Temperature Characteristics
Resistance to solder Heat
= ±
= ±
= ±
Solvent Resistant
7.1 Electrical
7.2 Mechanical
The Engineering Spec. for TBF-2012-245-R1 Band Pass Filter
Bending Test
Solderability
Drop Test
Vibration
ITEM
ITEM
Shock
RELEASED BY ﹕Steven-Tseng
DESIGNED BY ﹕Steven-Tseng
CHECKED
APPROVED BY ﹕Wang-Kevin
SCALE ﹕ X
Satisfy electrical characteristics
The Surface of terminal immersed shall
Satisfy electrical characteristics without
Satisfy electrical characteristics without
Satisfy electrical characteristics without
Marking should be legible without
be minimum of 95% covered with a new
coating of solder
distinct deformation in appearance
Mechanical damage such as break
Satisfy electrical characteristics without
mechanical damaged such as break
mechanical damage such as break
mechanical and distinct damage in
appearance
Satisfy electrical characteristics without
mechanical damage
Specification and Requirement
Specification and Requirement
BY ﹕Steven-Tseng
UNIT ﹕ X
THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF CYNTEC CO., LTD.
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE
MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION
DOCUMENT
乾坤科技股份有限公司
NO.
CYNTEC CO., LTD.
Solder the sample on PCB.
Exposure at each temperature,
-40℃, -20℃, 0℃, +25℃, +50℃,
+85℃ for 30minutes
Solder bath :
After immersing in flux, dip in245
+ 5 ℃ molten solder bath for 2 +
0.5 seconds
A. Pre-heat : 100 ~ 110 ℃ for 30
B. Immersed at solder bath of 270
Vibrate as apply 20 to 2,000Hz,
186m/s
amplitude for 2 hours in each of
three (X, Y, Z) axis (total 6 hours).
(1) Break value : 490 N
(2) Duration of pulse : 11ms
(3) 3 times in each positive and
Bending value : 3mm for 30 + 1
seconds
(1) Solvent : Trichloroethane or
Isopropyl alcohol.
(2) Immersed in solvent at room
temperature for 90 seconds
Drop the sample from a height of
1m to concrete ground for 10 times
seconds
negative direction of 3 mutual
perpendicular directions.
+ 5℃ for 20 + 1 seconds
2
(19G) acceleration 1.5mm
Test Method
Test Method
PAGE 4 OF 4
Preliminary
PAGE
REV.
A1