A1RAV NKK Switches, A1RAV Datasheet - Page 2

• Manufacturer Part Number: A1RAV
• Description: TOGGLE SWITCH, SPDT, HORIZ, ON-ON
• Manufacturer: NKK Switches
• Series: Ar

Specifications of A1RAV

• Contact Configuration: SPDT
• Switch Operation: (On)-On
• Contact Voltage Ac Nom: 28V
• Contact Voltage Dc Nom: 28V
• Contact Current Max: 100mA
• Switch Terminals: Through Hole
• Switch Mounting: PC Board
• Contact Form: SPDT
• Switch Function: (ON) - NONE - ON
• Contact Rating: 0.4 Volt-Amp at 28 VoltsAC/DC
• Termination Style: Vertical PC with Bracket
• Mounting Style: Through Hole
• Terminal Seal: Epoxy
• Contact Plating: Gold
• Actuator: Bat
• Power Capacity (va): 0.4 Volt-Amp
• Voltage Rating Ac: 28 Volts
• Actuator Style: Bat
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

General Specifications
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
PCB Processing
Standards & Certifications
www.nikkaiswitches.com • Nihon Kaiheiki • Phone [phone] • Fax [phone]
Operating Temperature Range:
Nominal Operating Force:
Insulation Resistance:
or CSA Certification:
Stationary Contacts:
Contact Resistance:
Dielectric Strength:
Movable Contact:
Support Bracket:
Mechanical Life:
Angle of Throw:
Contact Timing:
UL Recognition
Case Housing:
Electrical Life:
Logic Level:
Soldering:
Vibration:
Humidity:
Cleaning:
Toggle:
Shock:
Manual Soldering: 3 seconds maximum @ 350°C maximum.
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum between contacts for 1 minute minimum;
500V AC minimum between contacts & case for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum
1.47N (momentary); 1.18N (maintained) for .394” (10.0mm) toggles
2.73N (momentary); 1.84N (maintained) for all other toggles
Nonshorting (break-before-make)
26°
Glass fiber reinforced polyamide for antistatic; nickel plated brass for all others
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Brass with gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
Wave Soldering recommended. 5 seconds maximum @ 270°C maximum.
Automated cleaning. See Cleaning Specifications in Supplement section.
The A Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Process Sealed Subminiature Toggles
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Series A
2-06