A6KS-164RS-P Omron, A6KS-164RS-P Datasheet - Page 6

• Manufacturer Part Number: A6KS-164RS-P
• Description: SMT Rotary DIP
• Manufacturer: Omron

Specifications of A6KS-164RS-P

• Number Of Positions: 16
• Switch Type: DIP
• Actuator: Extended Shaft, Top
• Termination Style: SMD/SMT
• Contact Rating: 25 mA
• Operating Temperature Range: - 30 C to + 80 C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

A6K/A6KS
Safety Precautions
Note: Refer to Safety Precautions in the DIP Switches (Cat. No. X040) for details on general safety precautions.
The A6K/A6KS cannot be washed. Attempting to wash it may
result in malfunction due to flux and foreign matter from the PCB
flowing into the A6K/A6KS together with the cleaning fluid.
The type of flux or the amount or method in which it is applied,
including its use in reflow soldering, can have adverse effects on
Switch performance. Assess the proper flux, conditions, and
methods prior to using it.
The "RoHS Compliant" designation indicates that the listed
models do not contain the six hazardous substances covered by
the RoHS Directive.
Reference: The following standards are used to determine
compliance for the six substances.
6
• General Precautions for Soldering.
• Reflow Soldering
• Automatic Soldering Bath
• Manual Soldering
Correct Use
Make sure that Rotary DIP Switches are set to 0 before soldering.
Misalignment may result in reduced sensitivity due to the
soldering heat.
Observe the following conditions for reflow soldering.
(Measurement location: Top of Switch)
Soldering temperature: 260 °C max.
(Preheating: 150 °C
Soldering time: 5s max.
Soldering temperature: 350 °C max. at the tip of the soldering
iron Soldering time: 3s max.
Do not solder the Switch more than twice including any
rectification soldering. An interval of five minutes is required
between the first and second soldering.
Soldering
Washing
Using Flux
RoHS Compliant
Lead
Mercury
Cadmium
Hexavalent chromium : 1,000 ppm max.
PBB
PBDE
260 max.
230
180
150
•
120s max.)
Preheating
: 1,000 ppm max.
: 100 ppm max.
:1,000 ppm max.
: 1,000 ppm max.
: 1,000 ppm max.
60 to 150
Actual
soldering
60 max.
Time (s)
To prevent discoloration of the terminals and other problems during
storage, do not store the A6K/A6KS in locations subject to the fol-
lowing conditions.
Also, the A6K/A6KS is not waterproof or splash-resistant.
Do not install or use the A6K/A6KS in locations that are subject to
contact with water.
Do not subject the A6K/A6KS to freezing or condensation.
Do not apply excessive operating force to the Switch. Otherwise
the Switch may be damaged or deformed, and the switch
mechanism may malfunction as a result.
Set rotary-type DIP Switches with a flat-blade screwdriver that fits
into the screwdriver groove. Using a screwdriver of inappropriate
dimensions, or using a tool other than a flat-blade screwdriver
may cause damage to the groove that may make the Switch
impossible to operate. Extended-shaft models can also be
manually set, but be sure not to apply an excessive amount of
force to the Switch when setting it.
(1) High temperatures or humidity
(2) Corrosive gases
(3) Direct sunlight
Environment for Storage and Use
Handling
Packing Specifications
24±
1.5
11.5±
0.3
Perforations
+0.15
-0.05
1.75±
0.15
dia.
0.15
0
5
12±
2±
0.15
0.15
(7)
(4)
Tape drawing
direction
1.5
dia. holes
(P10=40±
P=4±
0.15
A6K/A6KS
0.3
Tape drawing
direction
)