SSG-01L1P-5 Omron, SSG-01L1P-5 Datasheet - Page 7

• Manufacturer Part Number: SSG-01L1P-5
• Description: Subminiature Basic Switch
• Manufacturer: Omron

Specifications of SSG-01L1P-5

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Precautions
■ Terminal Connections
When soldering a lead wire to a switch terminal, insert the wire con-
ductor into the hole of the switch terminal and take the following
steps promptly.
• Make sure that the capacity of the soldering iron is 60 W maximum.
• Be sure to apply only the minimum required amount of flux. The
• Use the following lead wires to connect to the solder terminals.
• Soldering Categories (Refer to the conditions of EN61058-1).
To automatically solder the Switch to a PCB in a soldering bath, com-
plete soldering within 5 seconds at a flux temperature of 250°C and
avoid the overflow of flux onto the surface of the PCB where the
Switch or other parts are mounted.
Simulated Hinge Lever
Hinge Roller Lever
SSG-01
SSG-5
Solder terminal
PCB terminal
Do not take more than 5 s to solder the switch terminal. Improper
soldering involving an excessively high temperature or excessive
soldering time may deteriorate the characteristics of the Switch.
SSG may have contact failures if flux intrudes into the interior of the
SSG.
SSG-01L3P
SSG-5L3P
SSG-01L3P-5
SSG-5L3P-5
SSG-01L2P
SSG-5L2P
SSG-01L2P-5
SSG-5L2P-5
Type
Type
AWG 22 to 20
AWG 20 to 18
Soldering iron used with soldering hole
Solder terminal type 1.2
Soldering bath used
Solder terminal type 1.2
Classified by EN61058-1
Conductor size
Wire the quick-connect terminals (#110) with receptacles. Insert the
terminals straight into the receptacles. Do not impose excessive
force on the terminal in the horizontal direction, otherwise the termi-
nal may be deformed or the housing may be damaged.
Insulation Distance
The Switch does not have a ground terminal. The minimum distance
through insulation (IEC61058-1) is 0.9 mm. If proper insulation for
the end product cannot be secured, additional insulation such as a
Separator or insulation cover should be attached.
Mounting
When securing the SSG, be sure to use M2.2 mounting screws and
tighten the screws with flat washers and spring washers securely
within a torque range between 0.20 to 0.24 N • m (2 to 2.5 kgf • cm).
Mounting Holes
Two 2.4-dia. mounting holes or M2.3 screw holes
Make sure that the plate to which the SSG is mounted is flat. If the
plate has protruding or warped part, the SSG may not operate prop-
erly.
Operating Stroke
Make sure that the operating stroke is 70% to 100% of the rated OT
distance. Do not operate the actuator exceeding the OT distance oth-
erwise the life expectancy of the SSG may be shortened.
Subminiature Basic Switch
OF max.
RF min.
PT max.
OT min.
MD max.
FP max.
OP
OF max.
RF min.
PT max.
OT min.
MD max.
FP max.
OP
Model
Model
SSG-01L3P
SSG-5L3P
0.60 N {61 gf}
0.06 N {6 gf}
—
1.0 mm
0.8 mm
18.9 mm
14.4
SSG-01L2P
SSG-5L2P
0.60 N {61 gf}
0.06 N {6 gf}
—
1.0 mm
0.8 mm
22.4 mm
17.9
+1.1
+1.1
/
/
-0.7
-0.7
SSG
mm
mm
SSG-01L3P-5
SSG-5L3P-5
0.20 N {20 gf}
0.02 N {2 gf}
SSG-01L2P-5
SSG-5L2P-5
0.20 N {20 gf}
0.02 N {2 gf}
7