SLCF2GBJI STEC, SLCF2GBJI Datasheet - Page 43
![no-image](/images/no-image-200.jpg)
SLCF2GBJI
Manufacturer Part Number
SLCF2GBJI
Description
Manufacturer
STEC
Type
CompactFlashr
Datasheet
1.SLCF2GBJI.pdf
(47 pages)
Specifications of SLCF2GBJI
Density
2GByte
Operating Supply Voltage (typ)
3.3/5V
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Package Type
Not Required
Mounting
Socket
Pin Count
50
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
3.18/4.75V
Operating Supply Voltage (max)
3.465/5.25V
Programmable
Yes
Lead Free Status / RoHS Status
Not Compliant
SLCFxxxJ(T2)(I)
Seek
(code: 7Xh)
This command is effectively a NOP command to the Card
although it does perform a range check.
Set Features
(code: EFh)
This command is used by the host to establish or select
certain features.
Set Multiple Mode
(code: C6h)
This command enables the card to perform Read and Write
Multiple operations and establishes the block count for these
commands.
Set Sleep Mode
(code: E6h or 99h)
This is the only command that allows the host to set the
ComapactFlash into Sleep mode. When the card is set to
sleep mode, the ComapactFlash clears the BSY line and
issues an interrupt. The card enters sleep mode and the only
method to make the card active again (back to normal
operation) is by performing a hardware reset or a software
reset.
Stand By
(code: E2h or 96h)
This command is sets the CompactFlash in Standby mode. If
the Sector Count Register is a value other than 0H, an Auto
Power Down is enabled and when the card returns to the idle
mode, the timer starts a countdown. The time is set in the
Sector Count Register.
Feature
CCH
BBH
01H
55H
66H
81H
Enable 8-bit data transfers
Disable Read Look Ahead
Disable Power on Reset (POR)
establishment of defaults at Soft Reset
Disable 8-bit data transfers
4bytes of data apply on Read/Write
Long commands
Enable Power on Reset (POR)
establishment of default at Soft Reset
Description
Document Part Number 61000-02805-111 March 2005
Stand By Immediate
(code: E0h or 94h)
This command causes the card to set BSY, enter the Standby
mode, clear BSY and return the interrupt immediately.
Translate Sector
(code: 87h)
This command allows the host a method of determining the
exact number of times a user sector has been erased and
programmed. This command is not supported.
Wear Level
(code: F5h)
This command is effectively a NOP command and only
implemented for backward compatibility. The Sector Count
Register will always be returned with an 00h indicating Wear
Level is not needed.
Write Buffer
(code: E8h)
This command enables the host to overwrite the contents of
the card’s sector buffer with any data pattern desired.
Write Long Sector
(code: 32h or 33h)
This command is provided for compatibility purposes and is
similar to the Write Sector(s) command except that it writes
516 bytes instead of 512 bytes.
Write Multiple
(code: C5h)
This command is similar to the Write Sectors command.
Interrupts are not presented on each sector, but on the
transfer of a block which contains the number of sectors
defined by Set Multiple command.
Write Multiple without Erase
(code: CDh)
This command is similar to the Write Multiple command
with the exception that an implied erase before the write
operation is not performed. Note that before using this
command, it is required to erase the repective sectors using
the Erase Sectors command.
COMPACTFLASH
Page 43