LXMG1618-05-42 MICROSEMI, LXMG1618-05-42 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/443/microsemi_sml.jpg)
LXMG1618-05-42
Manufacturer Part Number
LXMG1618-05-42
Description
Manufacturer
MICROSEMI
Datasheet
1.LXMG1618-05-42.pdf
(6 pages)
Specifications of LXMG1618-05-42
Operating Temperature Classification
Commercial
Pin Count
10
Lead Free Status / RoHS Status
Compliant
Copyright © 2002
Rev. 1.0a, 2006-11-13
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25°C except where otherwise noted.
Input Signal Voltage (V
Input Power ...................................................................................................................................................................... 5.5W
Output Voltage, no load .............................................................................................................Internally Limited to 1600V
Output Current............................................................................................................................ 7.5mA
Output Power.................................................................................................................................................................... 4.0W
Input Signal Voltage ( SLEEP Input) ................................................................................................................... -0.3V to 5.5V
Input Signal Voltage (BRITE)............................................................................................................................... -0.3V to 5.5V
Ambient Operating Temperature, zero airflow .................................................................................................... -20°C to 70°C
Storage Temperature Range .............................................................................................................................. -40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
¹ The minimum V
* The Inverter is capable of a lower output current than may be recommended by the panel manufacturer. It is the user responsibility to set the minimum
Output Power
Linear BRITE Control Input Voltage Range¹
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
Input Supply Voltage Range (Fully Regulated
Lamp Current)
Input Supply Voltage Range (Functional)
OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current
Full Bright Lamp Current
Full Bright Lamp Current
Full Bright Lamp Current
Min. Average Lamp Current
Lamp Start Voltage
Operating Frequency
² Total output power must not exceed 4W. Higher voltage lamps may require maximum output current to be set lower than 6.5mA
brightness (BRITE) input at or above the panel specification for minimum current
TM
terminal.
Parameter
BRT ADJ
Parameter
voltage depends on the panel characteristics, depending on the panel it can vary from 0.65V to 0.9V
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
IN1
R E C O M M E N D E D O P E R A T I N G C O N D I T I O N S ( R . C . )
) ................................................................................................................................... -0.3V to 6.5V
A B S O L U T E M A X I M U M R A T I N G S
E L E C T R I C A L C H A R A C T E R I S T I C S
Symbol
I
I
I
I
I
L(MAX)
L(MAX)
L(MAX)
L(MAX)
L(MIN)
V
f
LS
O
V
I
V
I
V
I
V
I
V
I
-20°C < T
V
SET1
SET1
SET1
SET1
SET1
BRT_ADJ
BRT_ADJ
BRT_ADJ
BRT_ADJ
BRT_ADJ
BRT_ADJ
Integrated Products
®
= Ground, I
= Ground, I
= Open, I
= Open, I
= I
Microsemi
Symbol
SET2
V
> 2.0V
> 2.0V
> 2.0V
> 2.0V
=0.65V
= 2.5V
V
I
BRT_ADJ
OLAMP
PanelMatch™
V
A
P
LAMP
T
< 70°C, V
IN1
= Ground
O
A
SET2
SET2
DC
DC
DC
DC
DC
DC
Test Conditions
SET2
SET2
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
, SLEEP > 2.0V, V
= Ground
= Open
.
= Ground
= Open
IN1
Recommended Operating Conditions
0.65 to 0.9
5V 4W CCFL Programmable Inverter Module
> 4.5V
4.75
Min
465
4.5
-20
5
DC
P
RODUCTION
IN1
IN1
IN1
IN1
IN1
( N O T E 1 )
IN1
= 5V
= 5V
= 5V
= 5V
= 5V
= 5V
R.C.
550
3.5
DC
DC
DC
DC
DC
5
5
D
ATASHEET
1300
Min
4.5
5.0
5.5
6.0
76
LXMG1618-05-4x
Max
635*
5.25
RMS
5.5
4.0
2.0
6.5
LXMG1618-05-4x
70
RMS
1400
Typ
1.5 *
(Internally Limited)
5.5
6.5
80
5
6
Max
5.5
6.0
6.5
7.0
83
mA
Units
V
°C
W
RMS
V
V
RMS
RMS
Units
mA
mA
mA
mA
mA
V
kHz
RMS
Page 2
RMS
RMS
RMS
RMS
RMS