1382350-1 TE Connectivity, 1382350-1 Datasheet - Page 2

• Manufacturer Part Number: 1382350-1
• Manufacturer: TE Connectivity

Specifications of 1382350-1

• Optical Fiber Type: TX/RX
• Data Transfer Rate: 1250Mbps
• Optical Rise Time: 0.26ns
• Optical Fall Time: 0.26ns
• Jitter: 0.08ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 845nm
• Package Type: SFP MSA
• Operating Supply Voltage (min): 3.135V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.465V
• Operating Temp Range: 0C to 70C
• Mounting: Snap Fit To Panel
• Lead Free Status / RoHS Status: Supplier Unconfirmed

2
©
For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at:
http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications.
Gigabit Ethernet Multimode
SFP MT-RJ Transceiver
Part Number 1382350-1
Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches
(if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners.
Gigabit Ethernet Multimode SFP MT-RJ Transceiver
Transmitter Performance Specifications:
(T
Parameter
Operating Data Rate
Optical Output (avg.)
Extinction Ratio
Transmit Disabled
Optical Output (avg.)
Center Wavelength
Spectral Width (RMS)
Relative Intensity Noise
Deterministic Jitter
Total Jitter
Output Rise Time
Output Fall Time
Pk-Pk Differential Input
Voltage
Transmit Fault
Voltage Levels
Transmit Disable
Voltage Levels
Power Supply Voltage
Supply Current
Operating Temperature
Note: All optical measurements made through a short patch cable, between 2 and 5 meters in length, using
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Tx_Fault_On
Tx_Fault_Off
Tx Disabled
Tx Enabled
C
=0 to 70°C, V
62.5 µm multimode fiber unless stated otherwise.
Meets Class 1 laser safety requirements of IEC 60825-1 and IEC 60825-2 and U.S. Department of Health
Services 21 CFR 1040.10 and 1040.11 when operated within the specified temperature and power supply
ranges.
Transmitter optical output power measured per TIA/EIA 455-95. Transmitter modulated with a valid
8b/10b data pattern. Specification applies for both 50 µm and 62.5 µm core multimode fiber.
Extinction ratio measured per TIA/EIA 526-4A with a repeating K28.7 data pattern.
Center wavelength and spectral width measured per TIA/EIA 455-127 using optical spectrum analyzer
with a valid 8b/10b data pattern.
RIN measured per ANSI X.230-1994 annex A with valid 8b/10b data pattern. RF power meter and current
meter test set replaced with microwave spectrum analyzer and calibrated high-speed photoreceiver.
Single mode fiber in test procedure replaced with multimode patch cable. Polarization rotator omitted.
DJ and TJ measured per IEEE 802.3Z Gigabit Ethernet Standard.
Measured from 20% to 80% points on rising and falling edge of transmitted waveform.
Transmitter optical waveform characteristics including rise time, fall time, pulse undershoot, pulse
overshoot, and ringing comply with the eye diagram shown in this document. These characteristics
are
performed using a receiver with a fourth-order Bessel Thompson filter.
Compatible with 10 K, 10 KH and 100 K ECL, PECL and LVPECL.
Open Collector/Drain output
controlled to help prevent excessive degradation of the receiver sensitivity. The eye mask test is
CC
-V
EE
=3.135 to 3.465V DC)
Symbol
V
P
RIN
CC
P
λ
V
OUT DIS
∆λ
DJ
t
t
TJ
I
T
–
TLH
THL
OUT
OUT
CC
- V
DIFF
C
12
EE
Notes
1,2
7,8
7,8
10
10
3
–
4
4
5
6
6
9
–
–
–
–
–
3.135
Min
-9.5
770
500
2.0
–
9
–
–
–
–
–
–
–
2
0
0
–
0
(Continued)
http://www.tycoelectronics.com/fiberoptics
Typ
845
3.3
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PDF Datasheet 1654843
V
3.465
3.465
Max
2000
1.25
0.85
-117
CC
860
227
260
260
-30
0.8
0.8
80
60
70
-4
–
+.3
Only available as PDF at:
Revised 11-03
Units
dB/Hz
Gb/s
dBm
dBm
mV
mA
nm
nm
dB
ps
ps
ps
ps
°C
V
V
V
V
V