DS11-1000 TE Connectivity, DS11-1000 Datasheet - Page 4

• Manufacturer Part Number: DS11-1000
• Manufacturer: TE Connectivity

Specifications of DS11-1000

• Input Type: DC
• Input Voltage (max): 32V
• Output Voltage (max): 60V
• Input Current (max): 15mA
• Output Device: MOSFET
• Pin Count: 6
• Mounting: Through Hole
• Operating Temperature Classification: Industrial
• Rad Hardened: No
• Output Type: DC
• Lead Free Status / RoHS Status: Not Compliant

4
Figure 7 - Temperature Derating Curve
Figure 9 - Outline Dimensions
Notes
1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). For Vcc levels above 6Vdc, a series limiting resistor is
2.Input transitions to be ≤ 1ms duration, and input direct drive should be “bounceless contact” type.
3. Vcc = 5Vdc for all tests unless otherwise specified.
4.All DS11 Series relays may drive loads connected to either positive or negative referenced power supply lines. Reversing polarity of output may cause permanent
5.Transient blocking voltage and electrical system spike tests are performed per MIL-STD-704 (28VDC systems).
6.To determine the maximum on-resistance at any given junction temperature, multiply on-resistance at 25°C (0.15 ohm) by normalized on-resistance factor from
7.Overload testing per MIL-R-28750 is constrained to the limits imposed by the short circuit protection requirements of this specification and DSCC drawing 88062.
8.Proper operation of the status feedback requires a status pull-up resistor. See Fig. 5 for status resistor value.
DS11-TBD–PDF–KRG–1-04
www.tycoelectronics.com
.890 MAX.
(22.60)
required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value from the curve.
damage. Inductive loads must be diode suppressed.
curve (Fig. 6).
Load circuit series inductance for “load shorted” mode of operation to be limited to 50mH max. Maximum repetition rate into a shorted load should not exceed 10
Hz.
TOLERANCE:
± 0.010 (0.25mm) FOR 2 PLACE DECIMALS,
± 0.005 (0.13mm) FOR 3 PLACE DECIMALS.
UNLESS OTHERWISE SPECIFIED
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
(15.24)
0
-50 -40 -20
.600
(2.79)
.110
(3.55)
.140
(12.70)
.500
Ambient Temperature (°C)
.530 MAX
(13.46)
(7.62)
.300
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
0
20 40 60 80 100 120
(5.08)
.200
DS11 Series High Performance Solid State Relays
DC solid state relay for loads up to 2A @ 60Vdc
.017 +.002, –.001 DIA.
(.43 + .05, –.02)
(6.93 ± .50)
6 PLS.
.273 ±.020
.020 MAX.
(.50)
.850 REF.
(21.59)
.190 MAX.
(4.82)
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
.490 REF.
(12.44)
DATE CODE
Figure 8 - Maximum Surge Current Without Tripping
TOP MARKING
HERE
ORIENT AS
SHOWN
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.01
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
-55°C
+85°C
+25°C
Time (seconds)
0.1
(Continued)
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
1
10