MPCBL0050N02Q Intel, MPCBL0050N02Q Datasheet - Page 56

• Manufacturer Part Number: MPCBL0050N02Q
• Manufacturer: Intel

Specifications of MPCBL0050N02Q

• Lead Free Status / RoHS Status: Supplier Unconfirmed

Table 21.
3.6.5
Table 22.
Intel NetStructure
Technical Product Specification
56
Pin
1
2
3
4
5
6
7
8
9
10
AP1[0]TX+
AP1[2]TX+
No Connect
AP1[6]TX+
No Connect
No Connect
No Connect
No Connect
No Connect
No Connect
A
®
J31 signal descriptions (Sheet 2 of 2)
Zone 3 Rear Transition Module Data Connector (J32)
This J32 connector is used to route signals from the AdvancedMC slots to the RTM.
AdvancedTCA RTM connector (Zone 3) J32 pinouts
AP0[x] are signals routed from AdvancedMC to the RTM.
Pin
A2-D3
A4 -H4
A5 -H5
A6-C6
D6-F6
G6
H6
G7-H7
A8-H9
A10-B10
C10
D10
E10
F10
G10
H10
• AMC_Port 20 is mapped to AP0[0]
• AMC_Port19 to AP0[1]
• AMC_Port18 to AP0[2]
• AMC_Port17 to AP0[3]
MPCBL0050 Single Board Computer
AP1[0]TX-
AP1[2]TX-
No Connect
AP1[6]TX-
No Connect
No Connect
No Connect
No Connect
No Connect
No Connect
B
Signal
SA[x]TX+, SA[x]TX-,
SA[x]RX+, SA[x]RX-
Eth0_D[x]
Eth1_D[x]
Eth0_Link,/Act/Spd
Eth1_Link,/Act/Spd
PCI_INTA
PCI_RESET#
PCIe_Clk_1
P[x]TX/Rx
USB[0]+, USB[0]-
DSR#
RXD#
RTS#
TXD#
CTS#
DTR#
AP1[0]RX+
AP1[2]RX+
No Connect
AP1[6]RX+
No Connect
No Connect
No Connect
No Connect
No Connect
No Connect
C
AP1[0]RX-
AP1[2]RX-
No Connect
AP1[6]RX-
No Connect
No Connect
No Connect
No Connect
No Connect
No Connect
Comments
Serial Attached SCSI signals for transmit and receive portions of
differential pairs. Three SAS ports are routed to the RTM.
GbE portd C redirected from front board.
GbE port D redirected from front board.
LEDs for GbE port C
LEDs for GbE port D
PCI INT
PCI reset signal required on all SBCs supporting PCI Express, but optional
for RTMs. This signal is used by devices that need to provide a PCI
interrupt but cannot always rely on MSI (Message Signaled Interrupt) to
be implemented properly.
PCI-Ex x4 Clock
PCI-Ex x4 lanes connected to ICH
USB data signals. Note that the RTM’s 5 V power for the USB connections
must be derived from the 12 V rail.
Data Set Ready signal for COM1 RS-232 connection.
Received Data signal for COM1 RS-232 connection.
Ready to Send signal for COM1 RS-232 connection.
Transmit Data signal for COM1 RS-232 connection.
Clear to Send signal for COM1 RS-232 connection.
Data Terminal Ready signal for COM1 RS-232 connection.
D
AP1[1]TX+
AP1[3]TX+
AP1[5]TX+
AP1[7]TX+
SA_Tx[0]+
No Connect
No Connect
No Connect
No Connect
No Connect
E
AP1[1]TX-
AP1[3]TX-
AP1[5]TX-
AP1[7]TX-
SA_Tx[0]-
No Connect
No Connect
No Connect
No Connect
No Connect
F
MPCBL0050—Connectors and LEDs
AP1[1]RX+
AP1[3]RX+
AP1[5]RX+
AP1[7]RX+
SA_Rx[0]+
No Connect
No Connect
No Connect
No Connect
No Connect
Order Number: 318146-001
G
September 2007
AP1[1]RX-
AP1[3]RX-
AP1[5]RX-
AP1[7]RX-
SA_Rx[0]-
No Connect
No Connect
No Connect
No Connect
No Connect
H