RFM70-S QUASAR, RFM70-S Datasheet - Page 19

• Manufacturer Part Number: RFM70-S
• Description: MODULE, TRANSCEIVER, SMD, 2.4GHZ
• Manufacturer: QUASAR

Specifications of RFM70-S

• Modulation Type: GFSK
• Data Rate Max: 2Mbps
• Frequency Range: 2.4GHz To 2.527GHz
• Sensitivity: -85dBm
• Supply Voltage Range: 1.9V To 3.6V
• Supply Current: 23mA
• Interface Type: SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

N/A
N/A
N/A
1C
1D
Note: Don’t write reserved registers and registers at other addresses in register bank 0
Tel: +86‐755‐86096587 Fax: +86‐755‐86096602 E‐mail: [e-mail] http://www.hoperf.com
TX_FULL
TX_EMPTY
Reserved
RX_FULL
RX_EMPTY
ACK_PLD
TX_PLD
RX_PLD
DYNPD
Reserved
DPL_P5
DPL_P4
DPL_P3
DPL_P2
DPL_P1
DPL_P0
FEATURE
Reserved
EN_DPL
EN_ACK_PAY
EN_DYN_ACK
5
4
3:2
1
0
255:0
255:0
255:0
7:6
5
4
3
2
1
0
7:3
2
1
0
Table 4 Register Bank 0
00
X
X
X
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
R
R
R/W
R
R
W
W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The packet is repeatedly retransmitted as
long as CE is high. TX_REUSE is set by the
SPI command REUSE_TX_PL, and is reset
by the SPI command W_TX_PAYLOAD
or FLUSH TX
TX FIFO full flag
1: TX FIFO full; 0: Available locations in
TX FIFO
TX FIFO empty flag.
1: TX FIFO empty
0: Data in TX FIFO
Only '00' allowed
RX FIFO full flag
1: RX FIFO full
0: Available locations in RX FIFO
RX FIFO empty flag
1: RX FIFO empty
0: Data in RX FIFO
Written by separate SPI command ACK
packet payload to data pipe number PPP
given in SPI command
Used in RX mode only
Maximum three ACK packet payloads can
be pending. Payloads with same PPP are
handled first in first out.
Written by separate SPI command TX data
pay-load register 1 - 32 bytes. This register
is implemented as a FIFO with three levels.
Used in TX mode only
Read by separate SPI command
RX data payload register. 1 - 32 bytes.
This register is implemented as a FIFO with
three levels.
All RX channels share the same FIFO.
Enable dynamic payload length
Only „00‟ allowed
Enable dynamic payload length data pipe 5.
Enable dynamic payload length data pipe 4.
Enable dynamic payload length data pipe 3.
Enable dynamic payload length data pipe 2.
Enable dynamic payload length data pipe 1.
Enable dynamic payload length data pipe 0.
(Requires EN_DPL and ENAA_P0)
Feature Register
Only „00000‟ allowed
Enables Dynamic Payload Length
Enables Payload with ACK
Enables the W_TX_PAYLOAD_NOACK
command
(Requires EN_DPL and ENAA_P5)
(Requires EN_DPL and ENAA_P4)
(Requires EN_DPL and ENAA_P3)
(Requires EN_DPL and ENAA_P2)
(Requires EN_DPL and ENAA_P1)
RFM70
V1.0
19