LM4890ITPX National Semiconductor, LM4890ITPX Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM4890ITPX
Manufacturer Part Number
LM4890ITPX
Description
Manufacturer
National Semiconductor
Datasheet
1.LM4890ITPX.pdf
(30 pages)
Specifications of LM4890ITPX
Operational Class
Class-AB
Audio Amplifier Output Configuration
1-Channel Mono
Output Power (typ)
1x1@8OhmW
Audio Amplifier Function
Speaker
Total Harmonic Distortion
0.1@8Ohm@400mW%
Single Supply Voltage (typ)
3/5V
Dual Supply Voltage (typ)
Not RequiredV
Power Supply Requirement
Single
Rail/rail I/o Type
No
Power Supply Rejection Ratio
66dB
Single Supply Voltage (min)
2.2V
Single Supply Voltage (max)
5.5V
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
8
Package Type
uSMD
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM4890ITPX
Manufacturer:
NS/国半
Quantity:
20 000
P
T
THD+N
PSRR
I
I
P
THD+N
PSRR
DD
SD
Symbol
Symbol
SD
o
0
Electrical Characteristics V
The following specifications apply for the circuit shown in Figure 1 unless otherwise specified. Limits apply for T
25˚C. (Continued)
Electrical Characteristics V
The following specifications apply for for the circuit shown in Figure 1 unless otherwise specified. Limits apply for T
Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
allowable power dissipation is P
curves for additional information.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 5: Machine Model, 220 pF–240 pF discharged through all pins.
Note 6: Typicals are measured at 25˚C and represent the parametric norm.
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: For micro SMD only, shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase I
Note 9: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 10: ROUT is measured from each of the output pins to ground. This value represents the parallel combination of the 10k ohm output resistors and the two 20k
ohm resistors.
Note 11: If the product is in shutdown mode and V
If the source impedance limits the current to a max of 10 ma, then the part will be protected. If the part is enabled when V
no damage will occur, although operational life will be reduced. Operation above 6.5V with no current limit will result in permanent damage.
Note 12: All bumps have the same thermal resistance and contribute equally when used to lower thermal resistance. All bumps must be connected to achieve
specified thermal resistance.
Note 13: Maximum power dissipation (P
Equation 1 shown in the Application section. It may also be obtained from the power dissipation graphs.
Note 14: PSRR is a function of system gain. Specifications apply to the circuit in Figure 1 where A
of gain increase. A system gain of 10 represents a gain increase of 14dB. PSRR will be reduced by 14dB and applies to all operating voltages.
Output Power (8Ω)
Thermal Shutdown Temperature
Total Harmonic Distortion + Noise
Power Supply Rejection Ratio
(Note 14)
Quiescent Power Supply Current
Shutdown Current
Output Power (8Ω)
Output Power (4Ω)
Total Harmonic Distortion + Noise
Power Supply Rejection Ratio
(Note 14)
Parameter
Parameter
DMAX
= (T
DMAX
JMAX
–T
) in the device occurs at an output power level significantly below full output power. P
A
DD
)/θ
JA
exceeds 6V (to a max of 8V V
or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4890, see power derating
DD
DD
THD = 1% (max); f = 1kHz
P
V
Input terminated with 10 ohms to
ground
V
V
THD = 1% (max); f = 1 kHz
THD = 1% (max); f = 1 kHz
P
V
Input Terminated with 10 ohms to
ground
o
ripple
IN
SHUTDOWN
o
ripple
= 3V
= 0.15Wrms; f = 1kHz
= 0.1Wrms; f = 1kHz
= 2.6V
= 0V, I
= 200mV sine p-p
= 200mV sine p-p
o
(Notes 1, 2, 8)
Conditions
Conditions
= 0A, No Load
= 0V
(Notes 1, 2, 8)
5
DD
), then most of the excess current will flow through the ESD protection circuits.
V
= 2. Higher system gains will reduce PSRR value by the amount
JMAX
62 (f = 1kHz)
44 (f = 1kHz)
, θ
JA
(Note 6)
(Note 6)
Typical
Typical
217Hz)
217Hz)
56 (f =
44 (f =
, and the ambient temperature T
0.31
0.22
0.08
170
0.1
2.6
0.1
0.2
DD
LM4890
LM4890
is greater than 5.5V and less than 6.5V,
(Notes 7, 9)
(Notes 7, 9)
DMAX
Limit
Limit
0.28
150
190
45
SD
can be calculated using
by a maximum of 2µA.
A
=
A
. The maximum
www.national.com
A
mA (max)
= 25˚C.
µA (max)
(Limits)
˚C(max)
(Limits)
dB(min)
˚C(min)
Units
Units
dB
W
%
W
W
%