DPCI-204-1203MG SL Power Electronics Manufacture of Condor/Ault Brands, DPCI-204-1203MG Datasheet - Page 3

• Manufacturer Part Number: DPCI-204-1203MG
• Description: PS DPCI SWITCHER 200W QUAD OUT
• Manufacturer: SL Power Electronics Manufacture of Condor/Ault Brands
• Series: DPCIr
• Type: Isolatedr

Specifications of DPCI-204-1203MG

• Output: 5V, 3.3V, ±12V
• Number Of Outputs: 4
• Power (watts): 200W
• Mounting Type: Compact PCI®
• Voltage - Input: 36 ~ 72V
• Package / Case: Module
• 1st Output: 5 VDC @ 25A
• 2nd Output: 3.3 VDC @ 25A
• 3rd Output: 12 VDC @ 5.5A
• 4th Output: -12 VDC @ 500mA
• Size / Dimension: 6.34" L x 1.59" W x 5.06" H (161mm x 40.4mm x 128.5mm)
• Operating Temperature: 0°C ~ 40°C
• Power (watts) - Rated: 200W
• Efficiency: 75%
• Approvals: CE, CSA, EN, TUV, UL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

± 2% over input range and 0 to 100% load change.
1% p-p or 50 mV, whichever is greater.
Measured at mating connector with 20 µF
Open sense lead protection
(Outputs #1 and 2): 0.03% per degree centigrade
0.1% over 8 hours after 30 minutes warm-up.
(Outputs #1 and 2): Output voltage returns to within 1%
in less than 1 ms for a 50% load change. Peak transient
does not exceed 5%.
(Outputs #1 and #2): Protects load against power supply
induced overvoltage. Trip-point is factory set so that
output voltage cannot exceed 136% of nominal. Input
power must be recycled to reset.
All outputs are protected against overload and short
circuit, Automatic recovery upon removal of fault.
TTL compatible signal. Signal goes low 20ºC before an
overtemperature shutdown.
Amber LED illuminates upon a failure condition as per
the CPCI and DPCI series specifi cations.
Green LED illuminates with no presence of any
failure condition.
Contact closure to common turns on dc outputs.
Recessed pin for “make last, break fi rst” connection.
Contact closure to the negative sense line or a TTL
level “0” turns off dc outputs.
Built-in ORing diodes, slope program current sharing on
all outputs, and self aligning connector provide hot swap
and N+1 capabilities. Current sharing remains within
10% of the unit’s full output rating while units are in
thermal equilibrium.
Protected against reverse voltage up to supply
current rating. except for reverse voltage on output #4
on CPCI-200.
Condor D.C. Power Supplies, Inc. • 2311 Statham Parkway, Oxnard, CA 93033
800-235-5929 • 805-486-4565 • FAX [phone] • www.condorpower.com
GENERAL SPECIFICATIONS
15 cfm, 400 lfm airfl ow required for cooling.
Isolated from ground 50 Vdc (leakage current <20 µA)
Shuts down power supply if overheated.
Automatic recovery.
0 to 40º centigrade at full ratings; derate 2.5%
per degree centigrade from 40º to 70º centigrade.
Unit will start up at -20º centigrade.
Models are approved to UL1950; CSA 22.2 #234;
IEC 950 and TUV EN60950, Class 1 SELV.,
CE 72/23/EEC/93/68EEC (low voltage directive).
Two year guarantee includes labor and parts.
Guarantee applies to operation at full published
specifi cations at the end of 2 years.
“L” option: Leakage current less than 0.5 mA per unit. Will
require additional fi ltering for compliance to EMI specifi ca-
tions.
3U H x 8HP W, 160 mm board depth (see outline drawing).
Utilizes a 47 pin modular connector in accordance with
PICMG
3U H x 8HP W, 160 mm board depth (see outline drawing).
Utilizes a DIN “M” connector as referenced in the PICMG
Power Interface Specifi cation 2.11.
6U H x 8HP W, 160 mm board depth (see outline drawing).
Utilizes a 38 pin modular connector as referenced in the
PICMG
6U H x 8HP W, 160 mm board depth (see outline drawing).
Utilizes a 47 pin modular connector in accordance with
PICMG
®
®
®
Power Interface Specifi cation 2.11.
Power Interface Specifi cation 2.11.
Power Interface Specifi cation 2.11.
:
®